C-LIGHT telephone TEL:+86 132 6656 7067    
Language
C-LIGHT search

Cisco 1G SFP SX and LX Optical Module Interoperability Testing

By C-LIGHT Marketing 丨 Jul 7, 2025
Table of Contents

    A Gigabit Ethernet link can remain down even when both optical modules fit into their SFP cages, use LC connectors, and advertise a 1.25Gbps data rate. One common source of confusion is the assumption that 1000BASE-SX and 1000BASE-LX/LH are interchangeable because they belong to the same Gigabit Ethernet family. Their optical transmission characteristics are different, and a direct connection between an SX module and an LX module is not a standard interoperable link.

    This distinction matters when testing Cisco switches, replacing optical modules, or connecting equipment from different vendors. Successful interoperability depends on matching the optical physical-layer specification, not simply the connector, form factor, or nominal Ethernet speed. At the network level, however, a switch can connect separate SX and LX optical segments through its independent ports and forward Ethernet traffic between them.

    1. Why 1000BASE-SX and 1000BASE-LX/LH Need Separate Compatibility Tests

    1000BASE-SX and 1000BASE-LX/LH both provide Gigabit Ethernet connectivity through standard SFP optical interfaces. Their main difference is the optical transmission method and the fiber infrastructure for which they are designed.

    1000BASE-SX uses an 850nm optical signal over multimode fiber. It is primarily intended for short-distance links inside buildings, equipment rooms, and campus networks. 1000BASE-LX/LH operates at approximately 1310nm and is commonly deployed over single-mode fiber for longer connections.

    Because their operating wavelengths differ, an SX transmitter cannot be treated as a compatible optical source for an LX receiver, or vice versa. Connecting an SX module directly to an LX module through an ordinary duplex fiber patch cord does not create a standard 1000BASE-X optical link.

    Important testing distinction: SX and LX can coexist in the same Ethernet network, but they are not interchangeable modules for the same direct optical link. To test direct optical interoperability, use matching 1000BASE-SX interfaces or matching 1000BASE-LX/LH interfaces at both ends.

    2. Optical Characteristics: SX Versus LX/LH

    The optical specifications determine which fiber infrastructure each module can use and what conditions must be met for a stable connection.

    Parameter1000BASE-SX1000BASE-LX/LH
    Operating wavelength850nm1310nm
    Optical sourceShort-wavelength optical transmitterLong-wavelength optical transmitter
    Primary fiber typeMultimode fiber (MMF)Single-mode fiber (SMF)
    Typical fiber connectorDuplex LCDuplex LC
    Common reachUp to 550m on supported OM2 fiberUp to 10km on standard single-mode fiber
    Other supported fiber conditions220m on FDDI-grade 62.5μm MMF; up to 1km on specified laser-optimized 50μm MMFUp to 550m on specified MMF with mode-conditioning patch cord
    Typical applicationBuilding and data room connectionsCampus backbone and longer fiber links
    Direct SX-to-LX pairingNot a standard interoperable optical pairing

    1000BASE-SX: 850nm multimode transmission

    SX modules are designed for multimode fiber and use an 850nm optical wavelength. The supported distance depends on the fiber's core diameter and modal bandwidth, rather than the optical module alone.

    Representative Cisco distance specifications include:

    • 62.5μm FDDI-grade multimode fiber: up to 220m.

    • 62.5μm OM1 fiber: up to 275m.

    • 50μm OM2 fiber: up to 550m.

    • 50μm OM3, OM4, and OM5 fiber: up to 1km under the specified laser-optimized conditions.

    For practical compatibility testing, the fiber grade should be recorded together with the SFP part number. Two 850nm modules may establish a link, but the installed cable still determines whether the connection meets the intended distance and loss requirements.

    1000BASE-LX/LH: 1310nm transmission

    LX/LH modules are primarily associated with single-mode fiber. Cisco specifies a typical maximum reach of 10km over standard single-mode fiber for its conventional 1000BASE-LX/LH interface.

    Some LX/LH implementations can also operate over multimode fiber for distances up to 550m. This is not simply a matter of plugging an LX module into an ordinary multimode patch cord. A mode-conditioning patch cord is required for the specified legacy multimode applications to manage the laser launch conditions and reduce differential mode delay problems.

    3. Three Network Scenarios That Must Not Be Confused

    When engineers refer to SX/LX interoperability, they may be describing different network arrangements. Identifying the actual topology before testing prevents misleading results.

    Scenario A: SX-to-SX direct optical connection

    Two 1000BASE-SX SFP modules are connected using compatible multimode fiber. Both ends operate at 850nm and use matching Gigabit Ethernet optical interfaces.

    This is the appropriate arrangement for testing direct SX interoperability, including third-party SFP evaluation on Cisco equipment. The test should confirm module recognition, fiber compatibility, optical power, link establishment, and traffic performance.

    Scenario B: LX/LH-to-LX/LH direct optical connection

    Two 1000BASE-LX/LH modules are connected through single-mode fiber. Both endpoints use compatible 1310nm optical interfaces and meet the same Gigabit Ethernet physical-layer requirements.

    This is the normal direct-link configuration for LX/LH compatibility evaluation. If multimode fiber is used instead, the specified mode-conditioning patch cord and supported distance must be taken into account.

    Scenario C: SX and LX on separate switch ports

    A different arrangement is possible when the network uses a switch between two optical segments. For example, one switch port can connect to an SX-equipped access device through multimode fiber, while another port connects to an LX-equipped aggregation switch through single-mode fiber.

    The Cisco switch terminates the optical link on each port and forwards Ethernet frames through its switching fabric. The SX and LX modules do not communicate directly with one another across a single fiber connection; each forms a separate physical link with its own compatible remote interface.

    TopologyOptical PairingInteroperability Assessment
    Direct SX linkSX ↔ SX over MMFValid direct-link test
    Direct LX/LH linkLX/LH ↔ LX/LH over SMFValid direct-link test
    Direct mixed linkSX ↔ LX/LHNot a standard interoperable optical pairing
    Mixed-media switched networkSX access segment and LX/LH uplink segmentValid network architecture when each individual link is correctly matched
    Cross-vendor SX linkVendor A SX ↔ Vendor B SXSuitable for testing standards-based module interoperability
    Cross-vendor LX/LH linkVendor A LX/LH ↔ Vendor B LX/LHSuitable for testing standards-based module interoperability

    4. What to Check Before Installing the SFP in a Cisco Switch

    Even when the optical specification is correct, the module must still be accepted by the host equipment. Cisco compatibility depends on the exact switch model, port type, hardware configuration, and software release.

    Before testing, record the following information:

    • Switch identification: Full Cisco product identifier, hardware revision, and relevant expansion module.

    • Software release: IOS, IOS XE, or other platform software version.

    • Port capability: Whether the selected port supports a standard 1G SFP or a particular multi-rate SFP implementation.

    • Transceiver identification: Vendor name, part number, serial number, and EEPROM information.

    • Optical interface: SX or LX/LH classification, wavelength, fiber type, and transmission distance.

    • Diagnostic capability: Whether the module and host support DOM/DDM monitoring.

    The Cisco Optics-to-Device Compatibility Matrix should be used to check supported Cisco transceiver and device combinations. Do not assume that a module supported on one Catalyst or Nexus model is automatically supported on every Cisco switch.

    One additional detail is relevant to newer Cisco equipment: Cisco's SFP-1G-SX and SFP-1G-LH modules are specifically documented for certain 10G-capable, dual-rate, or tri-rate ports. Cisco states that these particular modules do not operate in 1G-only ports. This is a product-specific distinction, so the exact ordering code and port capability must be checked rather than relying on the generic SX or LX label.

    5. A Practical Procedure for SX and LX Interoperability Testing

    A useful test report separates host recognition from optical performance. The following procedure can be applied to both SX and LX/LH modules, with the fiber and optical measurements adjusted for each interface.

    Step 1: Record the test configuration

    Identify both network devices, their software releases, the selected ports, and the two transceiver part numbers. For a cross-vendor test, record the manufacturer and ordering code of each module separately.

    show version
    show inventory

    These commands provide platform and hardware information on many Cisco IOS and IOS XE systems. Equivalent commands and output formats vary by device family.

    Step 2: Check module recognition

    After installing the SFP, inspect the interface status, inventory output, and system logs. Confirm that the switch identifies the transceiver and does not report an unexpected hardware or module-support warning.

    show interfaces status
    show inventory
    show logging

    Record the detected vendor information and product identifier. A recognized module has passed an important host-identification check, but this does not prove that the optical connection is functional.

    Step 3: Match the optical interfaces

    For an SX test, connect two compatible 850nm SX modules using supported multimode fiber. For an LX/LH test, connect two compatible 1310nm modules using single-mode fiber.

    Check the connector polarity and make sure the transmit path at one end reaches the receive path at the opposite end. Clean and inspect the LC end faces before making the connection.

    Step 4: Check optical diagnostic information

    Where the SFP and switch support digital optical monitoring, inspect the optical and electrical measurements.

    show interfaces gigabitEthernet 1/0/1 transceiver detail

    Depending on the Cisco platform, the command may use a different interface identifier or command format. The available diagnostic fields can include:

    • Module temperature and supply voltage.

    • Transmitter bias current.

    • Transmit optical power.

    • Receive optical power.

    • High and low alarm or warning thresholds.

    Compare the readings with the exact module datasheet. DOM/DDM support is model-dependent, so an unavailable reading should not automatically be interpreted as a failed optical module.

    Step 5: Verify link establishment

    Check whether the interface and line protocol reach an operational state. Confirm that both ends operate at the intended Gigabit Ethernet rate and that no configuration issue is preventing the connection.

    show interfaces gigabitEthernet 1/0/1
    show interfaces status

    For each test, record the time taken for link establishment, interface state, speed, and any relevant system messages. Repeat the test after a controlled module reseat or cable replacement when investigating intermittent behavior.

    Step 6: Test traffic and link stability

    Once the link is up, use approved test equipment or a controlled traffic source to verify end-to-end Ethernet communication. Monitor packet delivery, throughput, CRC errors, input errors, and link transitions.

    For a mixed-media switched topology, test both optical segments independently before evaluating traffic across the switch. This makes it possible to identify whether a fault belongs to the SX access link, the LX uplink, or the switching configuration.

    6. The Special Case of LX/LH over Multimode Fiber

    One of the most important details in SX/LX deployment is that 1000BASE-LX/LH is not limited to single-mode fiber in every supported implementation. Cisco documents operation over multimode fiber up to 550m, but legacy multimode links require a mode-conditioning patch cord.

    The issue relates to how the 1310nm laser signal is launched into multimode fiber. An unsuitable launch condition can excite different propagation modes and produce differential mode delay. This can reduce the effective signal quality even when the fiber distance appears to be within the nominal limit.

    When is a mode-conditioning patch cord required?

    For the specified LX/LH multimode applications, the mode-conditioning patch cord is required according to the applicable IEEE implementation guidance. Cisco also notes that the patch cord specification differs between 50μm and 62.5μm multimode fiber.

    Before qualifying this configuration, verify:

    • The exact LX/LH transceiver model and its supported multimode application.

    • The installed multimode fiber core diameter and grade.

    • The correct mode-conditioning patch cord for that fiber type.

    • The optical power budget and supported distance.

    • The patch cord's correct orientation and connection to the transmitter side.

    Do not substitute an ordinary multimode patch cord for the required mode-conditioning assembly. An LX/LH link over legacy multimode fiber may fail to meet its specified performance even if the switch recognizes both SFP modules.

    7. Common SX/LX Troubleshooting Results

    Different failure symptoms point to different parts of the optical link. Recording the observed condition before replacing equipment can significantly reduce troubleshooting time.

    Observed ResultLikely CauseRecommended Check
    SX and LX modules connected directly, no linkDifferent optical wavelengths and PMD typesReplace with a matching SX-SX or LX/LH-LX/LH optical pair.
    SX link does not establishIncorrect fiber grade, polarity, connector condition, or optical lossVerify 850nm modules, MMF specifications, and LC connections.
    LX link over SMF remains downWavelength mismatch, faulty fiber path, or incompatible moduleConfirm 1310nm interfaces at both ends and inspect optical readings.
    LX link over MMF is unstableMissing or incorrect mode-conditioning patch cordVerify the fiber type and use the specified mode-conditioning assembly.
    Switch reports unsupported SFPModule identification or platform support restrictionCheck the exact switch model, software release, and compatibility information.
    Low receive optical powerDirty connector, excessive link loss, or damaged fiberInspect the optical path and measure the received power.
    Link is up but error counters increaseMarginal optical quality, fiber installation issue, or physical-layer mismatchReview optical readings and compare counters before and after traffic testing.
    One vendor's SFP works but another does notEEPROM coding, host compatibility, or module-specific specificationsTest each part number on the same port and software configuration.

    8. C-LIGHT 1.25G SFP Optical Options for Cisco Network Evaluation

    For Gigabit Ethernet deployments, C-LIGHT offers 1.25G SFP optical transceivers covering different wavelengths, fiber types, and transmission distances. The portfolio includes short-distance multimode products and longer-distance single-mode configurations.

    The C-LIGHT 1.25G SFP product portfolio lists multiple 850nm, 1310nm, and 1550nm options. The following models illustrate the differences between its multimode and single-mode offerings.

    C-LIGHT ModelFiber TypeWavelengthListed DistanceConnectorCase Temperature Category
    CLSFP85GESXDMMF850nm550mLCCom. / Ind.
    CLSFP85GESXD-2KMMF850nm2kmLCCom. / Ind.
    CLSFP13GELXSMF1310nm20kmLCCom. / Ind.
    CLSFP13GELXDSMF1310nm20kmLCCom. / Ind.
    CLSFP13GEEXSMF1310nm40kmLCCom. / Ind.
    CLSFP15GEZXDSMF1550nm80kmLCCom. / Ind.

    The 850nm CLSFP85GESXD is a multimode 1.25G option listed for 550m, making it relevant to short-reach SX-type network applications. The 1310nm CLSFP13GELX is listed as a single-mode 20km module. Although its model name includes LX, its listed 20km reach should not automatically be treated as identical to the conventional 1000BASE-LX/LH 10km interface. The exact datasheet and optical specifications must be checked before assigning a standards-based interface designation.

    For Cisco network evaluation, the selected module should be tested against the exact switch model, port type, and software release. A successful result with one 1.25G SFP configuration does not automatically validate other wavelengths or reach options in the product family.

    C-LIGHT provides product selection and compatibility support for network equipment projects. Testing can be organized around the customer's actual Cisco platform, fiber infrastructure, required reach, and selected optical interface.

    9. What a Complete SX/LX Interoperability Report Should Record

    A useful test report should make it possible to reproduce the connection without relying on informal descriptions such as "Cisco compatible" or "1G link tested." Each result should identify the exact hardware and optical configuration.

    Record ItemInformation to Include
    Host equipmentCisco switch model, port number, hardware revision, and software version
    Optical modulesManufacturer, part number, serial number, and module type at each endpoint
    Optical specificationsWavelength, fiber type, nominal reach, connector, and optical power limits
    Fiber routeFiber grade, length, patch panels, splice points, and polarity
    Special componentsMode-conditioning patch cord, attenuator, or other required optical components
    Recognition resultEEPROM identification, module status, and system log information
    Optical diagnosticsDOM/DDM readings and measured optical power, where available
    Link resultInterface state, operating speed, and link stability
    Traffic resultThroughput, packet loss, CRC errors, and other relevant counters
    Test conclusionPass/fail result tied to the exact module, platform, and test configuration

    For cross-vendor testing, both transceiver manufacturers and part numbers should be documented. This helps separate optical-standard interoperability from vendor-specific host recognition behavior.

    10. Conclusion

    1000BASE-SX and 1000BASE-LX/LH serve different optical applications, even though both use Gigabit Ethernet SFP modules and commonly share a duplex LC connector. SX operates at 850nm over multimode fiber, while LX/LH operates at 1310nm and is primarily designed for single-mode fiber. Their optical differences mean that they should not be connected directly as a mixed SX-to-LX pair.

    Reliable interoperability testing begins by identifying the actual network topology, matching the optical interfaces at each direct link, checking Cisco platform support, and validating fiber conditions. Special attention should be given to mode-conditioning patch cords when LX/LH is deployed over legacy multimode fiber.

    C-LIGHT's 1.25G SFP portfolio provides 850nm multimode and 1310nm single-mode configurations for different Gigabit Ethernet applications. For Cisco deployments, each selected model should be checked against the intended port and tested with its actual optical link configuration before large-scale installation.

    Planning a Gigabit Ethernet optical deployment or evaluating SFP interoperability?

    C-LIGHT can assist with 1.25G SFP selection, fiber-interface requirements, transmission distance, and compatibility evaluation for Cisco network equipment.

    Contact C-LIGHT

    For any questions, please contact us by email or WhatsApp.

    Email: sales@c-light.com

    WhatsApp: +86 132 6656 7067

    Related Articles

    Call
    Top