C-LIGHT telephone TEL:+86 132 6656 7067    
Language
C-LIGHT search

100G QSFP28 Transceiver Interoperability Testing for ADTRAN Networks

By C-LIGHT Marketing 丨 Jul 26, 2025
Table of Contents

    100GbE connectivity is increasingly important in high-capacity access, aggregation, broadband, and enterprise networks. QSFP28 optical transceivers provide the bandwidth density required for these connections by combining four high-speed electrical lanes with corresponding optical transmission channels. When deploying third-party 100G QSFP28 modules in ADTRAN equipment, however, successful operation depends on more than the module's data rate and physical form factor.

    Interoperability must be evaluated across the host interface, module identification, optical architecture, fiber infrastructure, signal integrity, management functions, and Ethernet traffic performance. The exact ADTRAN platform and supported optical configuration are especially important because different QSFP28 modules may serve different applications, even when they share the same physical package.

    1. Understanding 100G QSFP28 Interoperability

    QSFP28 is a four-lane pluggable transceiver form factor commonly used for 100 Gigabit Ethernet. A typical 100G Ethernet implementation uses four electrical lanes operating at approximately 25Gb/s each. Depending on the optical technology, these signals may be transmitted through parallel fibers or combined into multiple wavelengths over a duplex single-mode fiber connection.

    For ADTRAN networks, interoperability testing should establish whether a particular QSFP28 module can:

    • Operate in the intended ADTRAN QSFP28 host port.

    • Be detected and identified correctly by the equipment.

    • Support the required 100GbE physical-layer interface.

    • Establish an optical link with the remote transceiver.

    • Maintain acceptable optical power and signal performance.

    • Transmit and receive Ethernet traffic without unacceptable errors.

    • Provide the expected management and diagnostic information.

    QSFP28 mechanical compatibility, host recognition, and successful 100GbE communication are separate requirements. A module should not be considered interoperable until the complete host-and-optic combination has been evaluated.

    2. ADTRAN Platforms Supporting 100G QSFP28 Optics

    ADTRAN's published Pluggable Optics Compatibility Matrix includes a dedicated QSFP28 category and identifies compatible host equipment for selected 100G optical modules. The listed applications include the Total Access 5000 SM200 and several SDX platforms.

    Examples of host platforms appearing in the compatibility information include:

    • Total Access 5000 SM200.

    • SDX 6020-48.

    • SDX 6320-16.

    • SDX 6330-48.

    • SDX 8205-54 and SDX 8205-54M.

    • SDX 8210-54.

    • SDX 8305-20.

    • SDX 8310-32 and SDX 8310-64.

    • SDX 8312-32.

    Not every QSFP28 optic is listed for every host. Compatibility must be checked against the exact part number and platform rather than inferred from the presence of a QSFP28 port.

    Network engineers should also distinguish standard 100GbE optical modules from QSFP28 DAC cables and specialized optical interfaces. These products may share a form factor but have different electrical, optical, and application requirements.

    3. Common 100G QSFP28 Optical Interfaces

    100G QSFP28 transceivers are available in several optical architectures. The choice depends on transmission distance, fiber type, connector configuration, and the physical-layer interface supported by the host.

    Optical TypeWavelengthFiber TypeTypical ReachOptical Interface
    100GBASE-SR4850 nmMultimodeUp to 100 m on suitable OM4 fiberMPO/MTP
    100GBASE-LR4Four LAN-WDM wavelengths around 1310 nmSingle-modeUp to 10 kmDuplex LC
    100G CWDM4Four CWDM wavelengthsSingle-modeTypically 2 kmDuplex LC
    100G ER4Four LAN-WDM wavelengths around 1310 nmSingle-modeUp to 40 kmDuplex LC
    100G ZR4Four LAN-WDM wavelengths around 1310 nmSingle-modeUp to 80 km, depending on implementationDuplex LC
    100G LR1Approximately 1310 nmSingle-modeUp to 10 kmDuplex LC

    These interfaces are not interchangeable simply because they all use QSFP28 packaging. For example, SR4 uses parallel multimode optical lanes and an MPO/MTP connection, while LR4 uses wavelength multiplexing over duplex single-mode fiber. The host and remote equipment must support the corresponding physical-layer technology.

    4. ADTRAN 100G QSFP28 Optical Part Numbers

    ADTRAN's compatibility matrix lists several 100G QSFP28 modules with different optical reaches and fiber configurations. The following examples illustrate the range of interfaces and the host compatibility information that should be checked before deployment.

    ADTRAN Part NumberData RateReachFiber / InterfaceOptical Configuration
    1445515F1C100 Gbps300 m on OM4Multimode850 nm parallel optics
    1445510F2C100 Gbps10 kmSingle-modeFour LAN-WDM channels
    1445510F2100 Gbps10 kmSingle-modeFour LAN-WDM channels
    1445513F1100 Gbps30 kmSingle-modeFour LWDM channels
    1445512F1C100 Gbps2 kmSingle-modeFour CWDM channels
    1445580F1100 Gbps80 kmSingle-modeExtended-reach LWDM configuration
    1445010F1C / 1445010F2C100 Gbps1 m / 2 mCopperQSFP28 direct-attach cable

    The matrix identifies host compatibility for the individual part numbers. The table is intended as a selection reference, not a statement that all modules are interchangeable or supported on every ADTRAN platform. Always check the latest host-specific entry and product documentation before ordering.

    5. C-LIGHT 100G QSFP28 Optical Transceiver Portfolio

    C-LIGHT provides a 100G QSFP28 product family covering multiple transmission distances and optical architectures. The portfolio includes short-reach multimode, single-mode duplex-fiber, and extended-reach configurations for different network environments.

    The product family uses the QSFP28 form factor and lists IEEE 802.3bm, SFF-8636, SFF-8665, and QSFP28 MSA-related interface specifications. Depending on the specific model, optical configurations include SR4, LR4, ER4, and ZR4 solutions.

    C-LIGHT 100G QSFP28 Optical Transceiver

    View C-LIGHT 100G QSFP28 Optical Transceiver Products and Datasheets

    The product range covers different optical interfaces and transmission distances, including 100 m, 2 km, 10 km, 20 km, 30 km, 40 km, 60 km, 80 km, and 100 km configurations. Actual reach depends on the selected product model and its optical specifications.

    100G QSFP28 LR4 for 10 km single-mode links

    The C-LIGHT CL100GQSFPCLR4 is a 100G QSFP28 LR4 optical transceiver designed for 10 km transmission over single-mode fiber. It uses four CWDM optical channels at 1270 nm, 1290 nm, 1310 nm, and 1330 nm, with a duplex LC interface.

    C-LIGHT CL100GQSFPCLR4

    • Aggregate bit rate: 103.1 Gb/s.

    • Optical architecture: 4 × 25.78 Gb/s channels.

    • Wavelengths: 1270 nm, 1290 nm, 1310 nm, and 1330 nm.

    • Fiber: Single-mode.

    • Maximum transmission distance: 10 km.

    • Optical connector: Duplex LC.

    • Power consumption: Below 3.5 W.

    • Digital management: I2C interface.

    View C-LIGHT 100G QSFP28 LR4 Product Details

    For ADTRAN applications, the LR4 module should be evaluated against the host's supported 100G optical interface, module identification requirements, and the remote-end transceiver. Its 10 km optical reach and duplex LC connection do not independently establish host interoperability.

    6. Matching C-LIGHT QSFP28 Modules to ADTRAN Network Applications

    Module selection should begin with the required link architecture. The following examples show how common network requirements relate to the C-LIGHT 100G QSFP28 product family.

    Network RequirementRelevant C-LIGHT ConfigurationSelection Considerations
    Short-reach 100GbE over multimode fiber100G QSFP28 SR4850 nm optics, OM3/OM4 fiber, MPO/MTP polarity, and reach
    Single-mode connection up to 2 km100G QSFP28 CWDM4Four CWDM channels, duplex LC, and remote-end wavelength compatibility
    Single-mode connection up to 10 kmCL100GQSFPCLR4 LR4Four CWDM channels, optical budget, and host support
    Extended-reach single-mode link100G QSFP28 ER4Receiver overload, dispersion, and total link loss
    Long-distance optical connection100G QSFP28 ZR4Optical power budget, attenuation, and link engineering

    These are application-based product selections. They should not be interpreted as confirmation that every C-LIGHT configuration has already been validated on every ADTRAN host. The exact module part number must be tested in the target equipment.

    7. QSFP28 Electrical Interface and Signal Integrity

    100G QSFP28 interoperability depends on both the optical interface and the high-speed electrical connection between the module and host. A typical 100G QSFP28 Ethernet interface uses four electrical lanes, each operating at approximately 25Gb/s.

    The electrical interface must maintain signal quality across the host PCB, connector, and transceiver. Signal-integrity issues can lead to link instability, lane errors, or degraded bit error rate performance.

    Important validation areas include:

    • High-speed lane signal integrity and electrical compliance.

    • Insertion loss and return loss across the host interface.

    • Transmitter and receiver electrical characteristics.

    • Clock and data recovery behavior, where applicable.

    • Power supply stability and module power consumption.

    • Host thermal conditions and module temperature.

    For optical modules that use retiming or additional signal processing, the host and module architecture must be compatible with the required electrical interface. A module's optical reach does not compensate for an unsupported host electrical configuration.

    8. Module Identification and Management Interface Verification

    QSFP28 modules contain identification and management information that the host can access through the module management interface. For supported modules, this information can include vendor identity, part number, serial number, temperature, supply voltage, and optical diagnostic values.

    QSFP28 management implementations commonly reference SFF-8636, while other modern pluggable form factors may use CMIS. The exact management behavior supported by the host should be confirmed through the equipment documentation.

    During interoperability testing, verify:

    • Whether the ADTRAN host detects the installed QSFP28 module.

    • Whether vendor and part-number information is read correctly.

    • Whether the module reports the expected data rate and optical type.

    • Whether temperature and voltage readings are available.

    • Whether TX and RX optical power readings are accessible where supported.

    • Whether warning and alarm flags behave as specified.

    Host recognition and diagnostic reporting should be documented separately from optical link performance. A module may establish a working link while some optional diagnostic fields remain unavailable due to host software or management implementation differences.

    9. Optical Power Budget and Fiber Link Validation

    After module recognition, the next stage is to verify the optical link. The transmitter and receiver must operate within their specified optical power ranges, and the total link attenuation must remain within the available optical budget.

    The basic optical budget can be estimated using the following relationship:

    Available optical budget (dB) = Minimum transmitter output power (dBm) − Receiver sensitivity (dBm)

    The total link loss includes fiber attenuation, connector insertion loss, splice loss, and other passive components. An appropriate engineering margin should be maintained rather than designing a link to operate at the receiver sensitivity limit.

    Parallel-fiber links

    For SR4 modules, verify the MPO/MTP connector configuration, fiber polarity, lane mapping, and fiber grade. Each transmit lane must connect to the corresponding receive lane at the remote end.

    Wavelength-multiplexed links

    For LR4, CWDM4, ER4, and ZR4 modules, verify the wavelength configuration, duplex LC fiber connection, optical power levels, and remote module type. Different multiplexing technologies should not be treated as interchangeable without checking the supported optical specifications.

    Long-distance links

    For extended-reach connections, additional attention should be given to receiver overload, chromatic dispersion, total attenuation, and the optical characteristics of the fiber path. An optical attenuator may be necessary in some low-loss configurations, depending on the receiver's maximum input power.

    10. ADTRAN 100G QSFP28 Interoperability Testing Procedure

    A repeatable testing process helps network operators and module suppliers evaluate interoperability under consistent conditions. The test should use the exact ADTRAN host platform and C-LIGHT module part number intended for deployment.

    Step 1: Identify the host equipment

    Record the ADTRAN platform, hardware revision, QSFP28 port, software version, and relevant interface configuration. Confirm that the selected port supports the intended 100GbE physical-layer interface.

    Step 2: Verify the module specification

    Record the C-LIGHT part number, optical type, data rate, wavelength, fiber type, connector, transmission distance, power consumption, and temperature range. Compare these details with the target ADTRAN host requirements.

    Step 3: Check module recognition

    Install the module according to the equipment manufacturer's procedures. Confirm whether the host detects the transceiver and reports the expected identification information. Record any unsupported-module messages or alarms.

    Step 4: Verify fiber connections

    Inspect the fiber connectors and confirm the correct fiber type, polarity, optical interface, and remote-end module. For SR4, verify MPO/MTP lane mapping. For duplex LC modules, verify the transmit and receive fiber paths.

    Step 5: Confirm optical power levels

    Check transmitter and receiver optical power using the available diagnostic functions or suitable calibrated test equipment. Compare the measured values with the module datasheet and the calculated link budget.

    Step 6: Establish the 100GbE link

    Verify that the port reaches the expected operational state. Check the interface status and relevant alarms through the supported equipment management interface.

    Step 7: Evaluate Ethernet traffic

    Run controlled traffic in both directions and monitor throughput, packet loss, CRC/FCS errors, interface drops, and link-state changes. The test duration and traffic profile should be defined before the evaluation begins.

    Step 8: Verify diagnostic monitoring

    Where supported, record module temperature, supply voltage, TX optical power, RX optical power, and alarm status. Compare host-reported values with the module specification and independent measurements when appropriate.

    Step 9: Document the result

    Record the exact host model, port, software version, module part number, fiber configuration, optical measurements, traffic results, and any limitations. The final compatibility statement should apply only to the configuration actually tested.

    11. Common 100G QSFP28 Interoperability Problems

    When a 100G QSFP28 module does not operate as expected, troubleshooting should separate host recognition, electrical interface, optical link, and Ethernet traffic issues.

    Observed ProblemPossible CauseVerification Focus
    Module not detectedUnsupported module, poor seating, or host interface issueHost compatibility, module installation, and equipment alarms
    Unsupported optic messageModule identification or platform support restrictionExact part number, host model, and software version
    Module detected but no linkIncorrect optical type, fiber polarity, or remote-side configurationPhysical-layer interface, remote optic, and fiber connection
    One or more optical lanes failFiber mapping error, connector contamination, or lane-specific issueLane mapping, optical power, and connector condition
    Low RX optical powerExcessive link loss, dirty connectors, or weak transmitter outputOptical measurements and fiber inspection
    Receiver overloadOptical input exceeds the receiver's permitted rangeRX power and link attenuation
    Intermittent linkMarginal optical budget, thermal conditions, or host configurationOptical power trends, temperature, and equipment logs
    High packet error rateSignal-integrity or optical-layer problemTraffic statistics, BER, and lane-level performance
    DDM information unavailableHost or module management implementation differencesManagement specification and software support

    12. C-LIGHT 100G QSFP28 Solutions for ADTRAN Network Applications

    C-LIGHT's 100G QSFP28 portfolio provides optical configurations for short-reach, campus, aggregation, and extended-distance network connections. The available options allow network designers to select a module according to fiber infrastructure, transmission distance, optical interface, and host requirements.

    100G QSFP28 SR4

    Designed for short-reach 100GbE connections over multimode fiber, SR4 uses parallel optical lanes and an MPO/MTP interface. It is suitable for compatible high-density switching and aggregation environments.

    View C-LIGHT 100G QSFP28 Product Options

    100G QSFP28 LR4

    The CL100GQSFPCLR4 supports 10 km single-mode transmission through four CWDM wavelengths and a duplex LC interface. It is intended for 100GbE connections where the link distance and optical budget match the module specification.

    View C-LIGHT CL100GQSFPCLR4 Product Details

    100G QSFP28 Extended-Reach Options

    For longer single-mode fiber connections, C-LIGHT's 100G QSFP28 portfolio includes extended-reach configurations. Selection should account for wavelength architecture, optical power budget, receiver overload, and the supported host interface.

    Explore C-LIGHT 100G QSFP28 Transmission Options

    For ADTRAN deployments, provide the exact switch model, host port, software version, target transmission distance, and preferred C-LIGHT part number when requesting compatibility evaluation. This information makes it possible to assess the appropriate optical configuration and define the required interoperability tests.

    13. Conclusion

    100G QSFP28 interoperability testing for ADTRAN networks requires a complete evaluation of host support, module identification, electrical signal integrity, optical compatibility, management functions, and Ethernet traffic performance. The QSFP28 form factor and 100GbE data rate alone do not guarantee successful operation.

    ADTRAN's published compatibility matrix provides a useful starting point for identifying supported 100G QSFP28 part numbers and host platforms. C-LIGHT offers a range of 100G QSFP28 optical modules covering multimode, single-mode, and extended-reach applications. Each selected module should nevertheless be evaluated on the intended ADTRAN equipment before production deployment.

    A documented interoperability process covering module recognition, optical power, link establishment, diagnostic monitoring, and bidirectional traffic testing provides a reliable basis for deployment decisions.

    For 100G QSFP28 module selection, ADTRAN network compatibility evaluation, or customized optical transceiver requirements, Contact C-LIGHT.

    For any questions, please contact us by email or WhatsApp.

    Email: sales@c-light.com

    WhatsApp: +86 132 6656 7067

    Related Articles

    Call
    Top