C-LIGHT telephone TEL:+86 132 6656 7067    
Language
C-LIGHT search

100G QSFP28 DR, FR and LR4 Transceiver Compatibility with Cisco Platforms

By C-LIGHT Marketing 丨 Jul 2, 2025
Table of Contents

    At 100GbE, the choice between DR, FR and LR4 optics affects more than the distance a fiber link can cover. These QSFP28 transceivers use different optical channel architectures, modulation formats and link budgets. A data center connection across a short single-mode fiber run may use 100GBASE-DR, an inter-rack or campus data center link may favor 100G-FR1, while 100GBASE-LR4 remains a widely deployed option for 10km single-mode fiber connections.

    For Cisco Catalyst, Nexus and other network platforms, successful deployment depends on several conditions working together: QSFP28 port support, transceiver identification, optical interoperability, host-side FEC configuration and stable traffic performance. Even when two modules share a duplex LC connector, they are not necessarily interchangeable.

    This article examines the technical differences between 100GBASE-DR, 100G-FR1 and 100GBASE-LR4, then outlines a practical compatibility evaluation framework for Cisco network equipment and third-party QSFP28 transceivers.

    1. Understanding 100GBASE-DR, 100G-FR1 and 100GBASE-LR4

    The three optical interfaces are designed for different link distances and use different approaches to transmitting 100Gbps Ethernet signals.

    Characteristic100GBASE-DR100G-FR1100GBASE-LR4
    Optical architectureSingle-lambdaSingle-lambdaFour-wavelength LAN-WDM
    ModulationPAM4PAM4NRZ across four optical lanes
    Optical channels1 × 100G1 × 100G4 × approximately 25G
    Typical wavelength1311nm region1311nm regionFour LAN-WDM wavelengths around 1295–1309nm
    Fiber typeSMFSMFSMF
    Standard reach500m2km10km
    ConnectorDuplex LCDuplex LCDuplex LC
    Common applicationShort-reach data center linksData center and campus interconnectsLonger-reach enterprise and data center links

    The table describes the common Ethernet implementations. Individual product specifications, host requirements and optical budgets must still be checked before deployment.

    100GBASE-DR: 500m single-mode connectivity

    100GBASE-DR uses one optical wavelength to carry a 100Gbps Ethernet signal over single-mode fiber. PAM4 modulation enables the required data rate on a single optical lane, reducing the number of optical channels compared with traditional four-lane designs.

    Its standardized reach is 500m, making it suitable for short single-mode fiber connections inside data centers and between nearby network equipment areas. The duplex LC interface also allows it to use conventional two-fiber single-mode cabling.

    100G-FR1: 2km single-lambda transmission

    100G-FR1 extends single-lambda PAM4 connectivity to 2km over single-mode fiber. It is designed for applications where the 500m reach of DR is insufficient but a 10km LR-class link is unnecessary.

    FR1 and DR share a single-lambda architecture, but their reach specifications and optical operating requirements differ. A DR module should not be treated as a substitute for FR1 simply because both use a 1310nm-region wavelength and duplex LC connector.

    100GBASE-LR4: Four-channel LAN-WDM transmission

    100GBASE-LR4 uses four optical wavelengths multiplexed onto a single fiber pair. Each optical lane carries approximately 25Gbps, producing an aggregate 100Gbps Ethernet connection over single-mode fiber.

    The four LAN-WDM channels operate around 1295nm, 1300nm, 1304nm and 1309nm. The interface supports a reach of up to 10km and is commonly used for building-to-building links, campus networks and data center interconnections.

    Although LR4 and single-lambda DR or FR1 modules may all use duplex LC connectors, their optical channel structures are different. They cannot be directly substituted without matching the optical interface at both ends.

    2. Optical Standards and Technical Differences

    Standards compliance is a central part of 100G transceiver interoperability. A QSFP28 module can fit into a port while still using an optical interface that the remote endpoint does not support.

    Technical ItemDRFR1LR4
    Ethernet specificationIEEE 100GBASE-DR100G-FR1 specification under 100G Lambda MSA / applicable IEEE implementationIEEE 100GBASE-LR4
    Optical signalingPAM4PAM4NRZ
    Electrical host interfaceCAUI-4CAUI-4CAUI-4
    Fiber connectionDuplex SMFDuplex SMFDuplex SMF
    Optical channel countOneOneFour
    FEC evaluationVerify applicable KP4/RS-FEC requirements and implementationVerify applicable KP4/RS-FEC requirements and implementationVerify host and module requirements for the specific LR4 implementation

    DR and FR1 use PAM4 signaling, which carries more information per symbol than NRZ. This higher signaling efficiency requires careful consideration of signal quality and forward error correction. LR4 uses four optical lanes with a different modulation architecture.

    FEC configuration matters: Do not assume that all 100G QSFP28 modules use the same FEC setting. Check the transceiver datasheet, Ethernet interface implementation and Cisco platform documentation. A mismatch in host-side FEC configuration can prevent a link from operating correctly or lead to an unstable connection.

    3. Cisco Platforms and QSFP28 Port Compatibility

    Cisco supports different 100G transceiver combinations across its Catalyst, Nexus and other product families. The availability of a QSFP28 cage does not mean that every DR, FR1 or LR4 module is supported on that device.

    Cisco PlatformTypical RoleCompatibility Checks
    Catalyst 9300XEnterprise access and aggregationExact switch model, uplink configuration, IOS XE release and supported 100G optics
    Catalyst 9500Campus core and distributionChassis SKU, interface type, software release and transceiver support
    Catalyst 9600Modular campus coreSupervisor, line card, port configuration and supported optical modules
    Nexus 9300Data center leaf and spineExact hardware model, NX-OS release, port mode and optical product ID
    Nexus 9500Data center modular switchingLine card, port speed, module support and software requirements
    Nexus 7000Data center core and aggregationSupervisor, line card and platform-specific transceiver list

    Compatibility varies within each product family. For example, Cisco's compatibility matrix lists 100G-FR support on certain Catalyst 9300X configurations with IOS XE 17.11.1, while LR4 and other optical types have different platform and software requirements. These entries should not be generalized to every Catalyst or Nexus switch.

    Use the Cisco Optics-to-Device Compatibility Matrix to identify supported Cisco transceiver and device combinations. Search by the exact network device product ID and optical module product ID, then check the minimum software release and any notes.

    Cisco documentation identifies products such as QSFP-100G-DR-S, QSFP-100G-FR-S and QSFP-100G-LR4-S as distinct optical products. Their individual compatibility entries should be checked rather than relying on the QSFP28 form factor alone.

    4. Why DR, FR1 and LR4 Are Not Interchangeable

    Several physical characteristics appear similar across these products, but their optical signals and operating specifications are not the same.

    Potential ConfusionTechnical DifferenceDeployment Impact
    Same QSFP28 form factorDifferent optical standards and channel architecturesHost support must be checked for the exact product type.
    Same duplex LC connectorDifferent wavelength and modulation requirementsConnector fit does not establish optical interoperability.
    Same 1310nm regionDR and FR1 have different reach specifications; LR4 uses four LAN-WDM channelsWavelength labels alone cannot determine compatibility.
    Same 100GbE data rateDifferent optical lane arrangements and signalingBoth endpoints must support the same Ethernet optical interface.
    Same single-mode fiber typeDifferent optical power budgets and reach limitsLink attenuation and receiver operating range must be verified.

    A DR-to-FR1 connection is not automatically supported just because both modules use single-lambda PAM4. Likewise, an LR4 module cannot be paired with a DR or FR1 module simply because the fiber patch cord and connectors are physically compatible.

    For a standard point-to-point Ethernet link, use matching optical interface types at both ends unless the manufacturer explicitly documents a supported interoperability combination.

    5. Cisco 100G QSFP28 Compatibility Testing Procedure

    A repeatable test should separate host recognition, optical link establishment and traffic performance. These are different stages, and each provides different evidence about compatibility.

    Step 1: Record the device and transceiver information

    Before installing a module, record:

    • Cisco switch model and product ID.

    • Hardware revision and installed line card, where applicable.

    • IOS XE or NX-OS software version.

    • QSFP28 interface number and configured port speed.

    • Transceiver manufacturer, part number and serial number.

    • Optical standard: DR, FR1 or LR4.

    • Fiber type, connector type and intended link distance.

    • Remote endpoint model and optical module information.

    For third-party module evaluation, preserve the exact module part number and coding information. Results from one product revision should not automatically be applied to a different revision.

    Step 2: Verify module recognition

    Use the commands supported by the specific Cisco platform to inspect the installed transceiver and interface state.

    show version
    show inventory
    show interfaces status
    show logging

    On supported IOS XE platforms, an interface-specific transceiver command may be available in this form:

    show interfaces HundredGigE1/0/1 transceiver detail

    On Nexus platforms, the interface name and command syntax may differ:

    show interface ethernet 1/1 transceiver details

    These are platform-dependent examples. Confirm the correct interface naming and command syntax in the documentation for the exact switch and software release.

    Record whether the device detects the module, displays its identification information and reports any unsupported-transceiver warning. A recognized module has passed an initial host-identification check, but this alone does not prove that the optical link is fully compatible.

    Step 3: Verify port configuration and FEC

    Confirm that the QSFP28 interface is configured for the intended 100GbE operation. Check whether the platform supports the selected optical type and whether the required FEC mode is available.

    For DR and FR1, pay particular attention to the PAM4 and RS-FEC/KP4 requirements specified by the module and host implementation. For LR4, verify the requirements of the exact module and Cisco interface. Do not apply a single FEC configuration to every 100G optical interface.

    Step 4: Establish the optical connection

    Connect matching optical interfaces at both ends using suitable single-mode fiber. Inspect the duplex LC connectors and ensure that the fiber path meets the distance and attenuation requirements.

    After connecting the link, inspect interface state and system logs. If the port remains down, verify the remote module type, port configuration, fiber polarity, connector condition and FEC settings before treating the transceiver itself as defective.

    Step 5: Inspect optical diagnostics

    Where Digital Optical Monitoring is supported, record the following information:

    ParameterPurposeEvaluation
    Module temperatureMonitors operating temperatureCompare with the module's specified operating range.
    Supply voltageChecks electrical supply conditionsCompare with the datasheet limits.
    Laser bias currentProvides transmitter operating informationReview against module-specific thresholds.
    Transmit optical powerMeasures outgoing optical powerCheck that output is within the specified range.
    Receive optical powerMeasures incoming optical powerCheck receiver sensitivity and overload limits.
    Alarm and warning flagsIndicate threshold violationsInvestigate the affected parameter and link conditions.

    For LR4, the module internally multiplexes four optical channels. Diagnostic information may expose channel-specific values depending on the module implementation and host support. For single-lambda DR and FR1, the diagnostic presentation may differ. Record the actual fields reported by the tested product rather than assuming all modules expose identical telemetry.

    Step 6: Validate traffic performance

    Once the physical link is operational, run a controlled traffic test between the endpoints. Record throughput, packet loss, interface errors and link transitions under a defined traffic profile.

    Useful checks include:

    • Basic connectivity between the two endpoints.

    • Traffic throughput at the intended line rate.

    • Packet loss under the selected test profile.

    • CRC and input error counters.

    • Link stability during sustained traffic.

    • System logs and transceiver alarms during operation.

    A test report should include the traffic profile and test duration. A port that remains up without carrying a representative traffic load has not completed a full operational evaluation.

    6. Common Compatibility Problems and Troubleshooting

    When a 100G QSFP28 link fails to establish or shows abnormal behavior, the cause may be in the host platform, optical interface, fiber path or port configuration.

    Observed ProblemPossible CauseRecommended Check
    Transceiver not recognizedUnsupported module coding or platform limitationCheck the exact product ID against Cisco compatibility documentation.
    Port remains downOptical mismatch, FEC configuration or fiber issueVerify both endpoints, interface settings and fiber continuity.
    DR and FR1 link mismatchDifferent reach specifications or host requirementsUse matching optical interfaces and verify the documented interoperability conditions.
    LR4 link failsWavelength mismatch, fiber issue or unsupported moduleVerify LR4 channel specifications and both endpoint modules.
    Low receive powerExcessive attenuation, dirty connector or damaged fiberInspect connectors and measure the optical path.
    High receive powerReceiver overload or unsuitable optical pathCompare receive power with the module's maximum input specification.
    CRC errors increasePhysical-layer issue, signal quality or configuration problemReview optical diagnostics, FEC status and interface counters.
    Intermittent link transitionsMarginal optical conditions, thermal issue or host behaviorReview event logs, temperature and optical readings over time.

    Changing the optical module without checking the link architecture can make troubleshooting more difficult. First confirm the exact standard at both endpoints, then investigate host recognition, configuration, fiber conditions and measured optical power.

    7. C-LIGHT 100G QSFP28 DR, FR1 and LR4 Solutions

    C-LIGHT's 100G QSFP28 portfolio includes both single-lambda PAM4 products and traditional multi-lane optical transceivers. These product categories support different data center and enterprise network distances.

    Single-lambda DR, FR1 and LR1 modules

    The C-LIGHT 100G QSFP28 Single Lambda portfolio lists the following products:

    ModelOptical StandardFiberWavelengthDistanceConnector
    CL100GQSFPDR1100GBASE-DRSMF1310nm region500mDuplex LC
    CL100GQSFPFR1100G-FR1SMF1310nm region2kmDuplex LC
    CL100GQSFPLR1100G-LR1SMF1310nm region10kmDuplex LC

    The DR1 datasheet identifies IEEE 802.3cu-2021 100GBASE-DR compliance, a QSFP28 MSA package, CAUI-4 electrical interface, 1311nm typical wavelength, duplex LC connector, 500m single-mode reach and a 0–70°C case operating temperature range.

    The LR1 datasheet identifies IEEE 802.3cu-2021 100GBASE-LR compliance, 1311nm typical wavelength, duplex LC connectivity and 10km single-mode reach. These are single-lambda products and should not be confused with four-channel LR4 transceivers.

    Traditional 100G QSFP28 LR4 modules

    For conventional four-channel 100G LR4 applications, C-LIGHT's 100G QSFP28 optical transceiver portfolio lists the CL100GQSFPLR4 model as a 10km single-mode product using four LAN-WDM channels and a duplex LC interface.

    This is the relevant product category for networks designed around the traditional 100GBASE-LR4 optical interface. Before ordering, confirm the detailed datasheet's channel wavelengths, optical power limits, electrical interface and FEC requirements against the target Cisco equipment.

    Product identification: C-LIGHT also has a separate product-news page whose LR4 title describes 1270nm, 1290nm, 1310nm and 1330nm CWDM channels. Those wavelengths describe a CWDM-style four-channel implementation, not the conventional LAN-WDM wavelength set used by standard 100GBASE-LR4. For an LR4 compatibility project, use the exact product datasheet and verify the channel plan rather than relying on a page title alone.

    Compatibility evaluation for Cisco equipment

    C-LIGHT DR, FR1 and LR4 products can be included in independent Cisco platform evaluation projects. Each test should be tied to the exact module model, Cisco switch product ID, software release, port configuration and remote endpoint.

    Testing can cover module recognition, optical link establishment, diagnostic monitoring, FEC behavior and sustained traffic performance. The results should describe the actual tested configuration and should not be represented as Cisco certification or universal support across all Cisco devices.

    8. Building a Cisco 100G QSFP28 Test Matrix

    For system integrators and network operators working with multiple Cisco switch models, a structured test matrix makes the results easier to reproduce and maintain.

    Test ItemDRFR1LR4
    Host recognitionRecord module identification and warningsRecord module identification and warningsRecord module identification and warnings
    Port supportVerify exact Cisco model and softwareVerify exact Cisco model and softwareVerify exact Cisco model and software
    Optical interfaceConfirm DR at both endsConfirm FR1 at both endsConfirm LR4 at both ends
    Fiber pathSMF, up to 500mSMF, up to 2kmSMF, up to 10km
    FEC behaviorVerify applicable host and module requirementsVerify applicable host and module requirementsVerify implementation-specific requirements
    DOM monitoringRecord available diagnostic fieldsRecord available diagnostic fieldsRecord available diagnostic fields
    Traffic validationThroughput, loss and error countersThroughput, loss and error countersThroughput, loss and error counters
    Long-term operationLink stability and alarmsLink stability and alarmsLink stability and alarms

    Each test record should preserve the following information:

    • Cisco device model and hardware revision.

    • IOS XE or NX-OS software version.

    • Port number and operating configuration.

    • Optical module model, serial number and vendor identification.

    • Optical standard and remote-end module type.

    • Fiber type, length and connector configuration.

    • FEC configuration and link status.

    • DOM readings and alarm status where available.

    • Traffic test profile, duration and measured results.

    Classify the final result into three levels:

    • Host recognition: The Cisco device detects and initializes the module.

    • Optical interoperability: The two endpoints establish a stable physical link using the intended optical standard.

    • Operational validation: The link carries the required traffic without unacceptable errors or instability under the recorded test conditions.

    9. Conclusion

    100GBASE-DR, 100G-FR1 and 100GBASE-LR4 address different 100GbE single-mode fiber requirements. DR provides 500m single-lambda connectivity, FR1 extends the same general architecture to 2km, and LR4 uses four LAN-WDM channels to support 10km links.

    For Cisco Catalyst and Nexus deployments, compatibility depends on more than the QSFP28 form factor. The exact switch model, software release, transceiver identification, optical standard, FEC behavior, fiber path and traffic performance all need to be considered.

    C-LIGHT provides 100G QSFP28 single-lambda and multi-channel optical solutions for different network applications. A product-specific compatibility evaluation can help identify the appropriate module and document its operation on the intended Cisco platform.

    Planning a 100G QSFP28 DR, FR1 or LR4 deployment?

    C-LIGHT can assist with optical product selection, technical specifications, compatibility evaluation and customized 100G connectivity requirements.

    Contact C-LIGHT

    For any questions, please contact us by email or WhatsApp.

    Email: sales@c-light.com

    WhatsApp: +86 132 6656 7067

    Related Articles

    Call
    Top