Data center access networks must connect large numbers of servers while keeping cabling manageable, maintaining sufficient bandwidth, and allowing hardware to be expanded without disrupting existing services. Two common physical deployment models are Top-of-Rack (ToR) and End-of-Row (EoR) switching. Both provide server access to the wider network, but they organize switches and cable infrastructure differently.
ToR places access switches inside individual server racks, keeping server-to-switch connections short and localized. EoR centralizes access switching equipment near the end of a server row, connecting multiple racks to a shared switching location. This changes the distribution of network hardware, horizontal cable requirements, port utilization, power consumption, and maintenance responsibilities.
The decision is not simply about choosing a switch location. It involves the relationship between server density, rack design, cable pathways, network expansion, redundancy, and the type of traffic the data center must support.
1. What Is ToR (Top-of-Rack) Switching?
Top-of-Rack switching is a data center deployment model in which one or more network switches are installed inside each server rack, commonly near the top. Servers and other equipment in the same rack connect directly to these switches through short copper or fiber-optic cables.
Each ToR switch aggregates the traffic generated by the rack's servers and forwards it through uplinks to an upstream network layer. In a modern spine-leaf fabric, the ToR switch commonly performs the leaf role and connects to multiple spine switches.
A typical ToR deployment has the following characteristics:
Local server connections: Server-to-switch cables remain within the same rack in the conventional ToR arrangement.
Distributed access switching: Each rack has its own access-switch capacity rather than relying on a shared access switch at the end of a row.
Short cable runs: DAC, AOC, copper Ethernet, and short optical connections may be selected according to interface speed and distance.
Rack-level expansion: New server racks can be equipped with their own access switches and connected to the upstream fabric.
Localized fault management: Switches, server ports, and local connections can be identified and maintained within individual racks.
ToR is particularly useful when racks are deployed as independent, standardized units. A rack can be assembled with servers, access switches, power distribution, and local cabling before being connected to the wider data center infrastructure.
2. What Is EoR (End-of-Row) Switching?
End-of-Row switching places access switches in a dedicated network rack or switching cabinet at the end of a row of server racks. Instead of installing a separate access switch in every server rack, the EoR equipment provides network ports for servers distributed across multiple racks.
Server connections travel through horizontal cabling pathways, such as overhead cable trays or underfloor cable routes, to the EoR switching location. Structured cabling and patch panels are frequently used to organize these connections and make port changes easier to manage.
Typical EoR characteristics include:
Centralized access switching: A shared switching platform serves servers in multiple cabinets.
Longer horizontal cable runs: Server connections must reach the centralized switching location.
Higher port consolidation: Larger modular switches or higher-density platforms can serve multiple racks.
Structured cabling: Patch panels and permanent cable links can organize connections between server cabinets and network equipment.
Centralized maintenance: Access switches and many associated ports can be managed from a dedicated network location.
EoR is often associated with modular switching systems or high-density access platforms. However, the essential characteristic is the physical placement of access switching at the row level, not a particular switch manufacturer, chassis type, or routing protocol.
3. ToR vs EoR: Key Differences
The main difference between ToR and EoR is where access switching takes place and how server connections reach the switches. ToR distributes switching equipment across individual racks, while EoR consolidates it in a shared location.
| Feature | ToR (Top-of-Rack) | EoR (End-of-Row) |
|---|---|---|
| Switch location | Inside or near the top of each server rack | In a dedicated network rack at the end of a server row |
| Switch distribution | Distributed across individual racks | Centralized for multiple server racks |
| Server cabling | Short connections within the rack | Horizontal cable runs from server racks to the EoR location |
| Number of access switches | Usually higher across the data center | Can be lower because switches serve several racks |
| Port utilization | May be lower when individual racks are not fully populated | Ports can be allocated across multiple racks |
| Cable infrastructure | Less horizontal cabling between servers and access switches | More extensive horizontal cabling and cable management |
| Switch management | More distributed devices to configure and maintain | More centralized access-switch management |
| Power and cooling | Switch power and heat are distributed among server racks | Switch power and heat are concentrated in network racks |
| Rack expansion | Supports modular rack-by-rack deployment | Requires sufficient centralized port and cabling capacity |
| Common applications | Hyperscale facilities, modular deployments, and spine-leaf fabrics | Centralized access networks and facilities with established structured cabling |
4. ToR and EoR Network Layouts
The physical arrangement of switches and cables is easier to understand by looking at how server racks connect to access equipment.
ToR layout
Each rack has local server connections and separate uplinks to the upstream network.
In this arrangement, each rack has its own access-switch ports. Server connections are short, and the access switch aggregates traffic before forwarding it upstream. A rack can be added as a relatively independent unit, provided the upstream network has sufficient capacity.
EoR layout
Server connections from multiple racks run through horizontal cabling to centralized EoR switches.
In the EoR arrangement, access-switch ports are consolidated in a network rack. Servers in several cabinets connect to this shared switching location through the structured cabling system. This can improve port utilization, but it requires careful planning for cable routes, patching, labeling, and future capacity.
5. Cabling Requirements and Infrastructure
Cabling is one of the most significant factors when selecting a ToR or EoR design. The two models distribute cable lengths and connection points differently, affecting installation work, physical space, troubleshooting, and upgrade planning.
ToR cabling: Server-to-switch connections are generally short and contained within each rack. DAC cables, AOCs, copper Ethernet, and optical patch cables can be used according to the link requirements. The main cabling challenge is maintaining consistent connections across many individual racks and organizing their uplinks.
EoR cabling: Server-to-switch connections must travel from each server cabinet to the centralized network rack. This generally requires more horizontal cable infrastructure, cable trays, fiber distribution, or structured copper cabling. Patch panels can provide a controlled cross-connect point between permanent cable runs and equipment patch cords.
| Cabling Consideration | ToR | EoR |
|---|---|---|
| Local cable length | Short server-to-switch connections | Longer server-to-switch connections |
| Horizontal cable volume | Generally lower for server access | Generally higher for connections from multiple racks |
| Patch-panel requirements | May be simpler or limited to selected links | Often useful for structured cross-connect management |
| Cable pathway planning | Focuses on local rack routing and uplinks | Requires planned pathways from multiple racks to the network rack |
| Connection changes | Usually handled locally within the rack | May involve patch-panel and centralized switch-port changes |
| Future speed upgrades | Can be localized to individual racks | Depends on the bandwidth and media capacity of the installed cable plant |
The installed cable plant should be selected with future Ethernet speeds and connection densities in mind. For optical infrastructure, fiber type, connector design, polarity, attenuation, patch-panel insertion loss, and link distance all need to be considered. High-speed links may require parallel-fiber assemblies or duplex single-mode connections depending on the selected transceiver technology.
6. Port Utilization, Switch Count and Total Cost
ToR and EoR distribute access-switch ports differently. This affects how efficiently available ports are used and how much physical equipment is required throughout the facility.
In a ToR design, each rack has dedicated access-switch capacity. This arrangement makes rack-level deployment straightforward, but a partially populated rack may leave many switch ports unused. If the data center contains a large number of lightly populated racks, the total number of installed switches can increase significantly.
EoR consolidates access ports across multiple racks. If server populations are uneven, centralized port allocation can reduce the number of unused ports. A larger switching platform may serve more endpoints without requiring a separate access switch in every server cabinet.
| Cost Factor | ToR Considerations | EoR Considerations |
|---|---|---|
| Switch hardware | More individual switches may increase equipment count | Fewer high-density or modular switches may serve several racks |
| Port utilization | Unused ports may increase when racks are lightly populated | Ports can be allocated among a larger server group |
| Cabling installation | Less horizontal access cabling is generally needed | More horizontal cable, patching, and pathway infrastructure may be required |
| Power consumption | Distributed across server racks | Concentrated in network racks |
| Cooling | Access-switch heat adds to rack-level thermal load | Dedicated network-rack cooling capacity may be needed |
| Maintenance | More devices may require configuration and lifecycle management | Fewer access devices can simplify centralized management |
Neither architecture is automatically less expensive. ToR can reduce horizontal cabling and simplify incremental deployment, while EoR can improve port consolidation and reduce the number of access switches. A reliable cost calculation should include switches, optics, transceivers, cables, patch panels, installation, power, cooling, maintenance, and the cost of future changes.
7. Network Performance, Latency and Redundancy
ToR and EoR do not inherently determine Ethernet forwarding performance. Actual performance depends on switch capacity, interface speed, oversubscription, traffic distribution, buffering, routing design, and the number of forwarding hops.
ToR can provide direct local switching between servers connected to the same rack switch. Traffic that needs to reach other racks travels through the upstream network. In a spine-leaf fabric, the ToR switch commonly forwards inter-rack traffic toward a spine switch and then to the destination leaf.
EoR can provide direct port-to-port forwarding for servers connected to the same centralized access switch. However, connections to servers outside that switch's local forwarding domain may require additional network hops. The final result depends on how access switching and the upstream fabric are designed.
Redundancy must also be planned at both the server access and upstream network levels:
ToR redundancy: Two ToR switches can provide independent server connections and separate upstream paths.
EoR redundancy: Two independent EoR switching systems can serve the same server group, with suitable dual-homed server connections.
Uplink diversity: Multiple uplinks should be distributed across independent upstream devices and, where practical, separate physical cable routes.
Power resilience: Redundant power feeds and appropriate power-supply arrangements help reduce equipment-related outages.
Failure-domain planning: A centralized EoR platform can affect multiple racks if it fails, while a single ToR failure can affect the servers connected to that rack's switch.
Redundant switches do not automatically guarantee uninterrupted service. Network protocols, server NIC configuration, link aggregation or multihoming, routing convergence, and physical-path separation all determine how effectively traffic can continue during a failure.
8. Optical Connectivity in ToR and EoR Networks
Optical connectivity plays an important role in both deployment models, particularly as data center interfaces move toward 100G, 400G, 800G, and higher bandwidths. The primary difference is where optical links are used and how their distances are distributed across the facility.
In ToR architecture, optical transceivers are commonly used for uplinks between rack-level access switches and the upstream spine or aggregation layer. Short server connections may use DAC or AOC assemblies when supported by the equipment and link distance. Fiber-optic connections become increasingly relevant when rack-to-rack or rack-to-network-room distances exceed practical copper reach.
In EoR architecture, optical links may be used for longer connections between the server-row cabling infrastructure and centralized switching equipment. The selection depends on the installed fiber plant, required port speed, optical reach, connector type, and switch interface compatibility.
| Connectivity Type | Typical Application | Selection Factors |
|---|---|---|
| DAC | Short connections between servers and nearby switches | Distance, port compatibility, cable routing, and power requirements |
| AOC | Short-to-medium optical connections between compatible equipment | Supported interface, cable length, power, and endpoint compatibility |
| 100G Optical Transceiver | High-speed server, access, or fabric uplinks | Wavelength, fiber type, connector, reach, and link budget |
| 400G Optical Transceiver | High-capacity connections between access and upstream network layers | Form factor, Ethernet standard, lane configuration, and optical interface |
| 800G Optical Transceiver | High-bandwidth data center fabrics and AI infrastructure | Switch port support, module power, cooling, fiber layout, and reach |
For ToR and EoR deployments, C-LIGHT provides a range of optical transceiver solutions for data center and high-speed Ethernet connectivity. The appropriate module should be selected according to the exact switch model, supported data rate, optical standard, wavelength, fiber type, connector, distance, and link budget.
For large deployments, optical link planning should also account for patch-panel connections, fiber polarity, insertion loss, cleaning requirements, and future port-speed upgrades. A centralized EoR cable plant may need additional structured fiber distribution, while a ToR design requires consistent uplink planning across individual server racks.
9. When Should You Choose ToR or EoR?
The appropriate architecture depends on how the data center is built and operated. Rack density, server deployment patterns, existing structured cabling, switching capacity, and expansion plans should all influence the decision.
ToR is often suitable when:
New server racks are deployed incrementally or as standardized units.
Short server-to-switch connections and reduced horizontal cabling are priorities.
Rack-level fault isolation and independent expansion are important.
The network design uses a distributed spine-leaf fabric.
There is sufficient rack power and cooling capacity for additional access switches.
EoR is often suitable when:
Several server racks share a centralized switching location.
Existing structured cabling is already installed and suitable for the required speeds.
Higher port utilization is important across multiple server cabinets.
Centralized switch management and maintenance are operational priorities.
Dedicated network racks can accommodate switching hardware, cabling, and cooling requirements.
| Data Center Requirement | Potentially Suitable Model | Reason |
|---|---|---|
| Modular rack-by-rack deployment | ToR | Each rack can be equipped and connected independently. |
| Many lightly populated server racks | EoR | Shared access ports may improve utilization. |
| Reduced horizontal server cabling | ToR | Most server connections remain within each rack. |
| Existing centralized structured cabling | EoR | The existing cable plant may support centralized access switching. |
| Localized access-switch maintenance | ToR | Access equipment is distributed by rack. |
| Centralized access-switch management | EoR | Access equipment is consolidated in network racks. |
| High-density AI server racks | Depends on rack, thermal, and fabric design | Switch placement, power, cooling, bandwidth, and cable reach must be evaluated together. |
10. MoR as an Alternative Between ToR and EoR
Middle-of-Row (MoR) switching provides another physical deployment option. Instead of placing switches inside each server rack or at the very end of a row, MoR positions access switches near the middle of the row.
This arrangement can reduce the longest cable runs associated with EoR while still consolidating switching equipment outside individual server racks. It is useful when the distance to a single end-of-row location becomes inconvenient or when a facility has several groups of server cabinets.
| Model | Switch Position | Primary Design Characteristic |
|---|---|---|
| ToR | Inside each server rack | Distributed switching with short local server connections |
| MoR | Near the middle of a server row | Centralized switching with more balanced cable distances |
| EoR | At the end of a server row | Centralized switching with longer horizontal connections from some racks |
MoR does not eliminate the trade-offs between distributed and centralized switching. It changes the physical location of the switching equipment and may provide a practical compromise for a particular row layout.
11. Conclusion
ToR and EoR are two established approaches to organizing access switching in data centers. ToR distributes switches across server racks, reducing local server cabling and supporting modular rack deployment. EoR consolidates access switches near the end of a row, improving port sharing and centralizing equipment management while requiring more extensive horizontal cabling.
There is no universal winner. ToR can be attractive for new data centers that prioritize modular deployment, short connections, and distributed network access. EoR can remain effective in facilities with established structured cabling, centralized access requirements, or server populations that benefit from shared switch capacity.
As data center bandwidth requirements continue to increase, switch placement must be considered alongside optical connectivity, port density, redundancy, power, cooling, and future network expansion. The strongest design is the one that balances these requirements across the entire facility rather than optimizing only the location of the access switches.
For high-speed Ethernet and data center optical connectivity requirements, visit C-LIGHT Optical Transceivers or Contact C-LIGHT.
TEL:+86 132 6656 7067




















































>
>
>
>
>
>
>
>