C-LIGHT telephone TEL:+86 132 6656 7067    
Language
C-LIGHT search

What Is the Role of Redrivers in High-Speed Cables?

By C-LIGHT Marketing 丨 Jul 2, 2025
Table of Contents

    Redrivers are active analog signal-conditioning components used in high-speed cable assemblies to compensate for signal degradation during electrical transmission. Their main function is to restore signal amplitude and improve waveform quality through equalization and amplification, helping high-speed signals travel across channels with significant insertion loss.

    As data rates increase in 100G, 400G, and 800G networking, electrical signals become more sensitive to attenuation, inter-symbol interference (ISI), and channel distortion. Redrivers help address these challenges in active copper cables (ACC) and other high-speed electrical interconnects.

    Unlike retimers, redrivers do not recover clock and data or regenerate the transmitted bitstream. They process the analog waveform directly, making them a lower-complexity signal-conditioning option for applications where the channel can remain within the receiver's timing and jitter budget.

    1. What Is a Redriver in a High-Speed Cable?

    A redriver is an analog integrated circuit designed to compensate for signal degradation in high-speed electrical channels. It receives an attenuated electrical signal, applies equalization, and produces a conditioned output for the next part of the transmission path.

    In high-speed cable assemblies, redrivers are typically integrated into the cable-end electronics. Their purpose is to compensate for the frequency-dependent loss introduced by copper conductors, connectors, and other parts of the electrical channel.

    Most high-speed redrivers use a continuous-time linear equalizer (CTLE). A CTLE applies frequency-dependent gain to compensate for the fact that high-frequency signal components are often attenuated more than low-frequency components during transmission.

    Depending on the device architecture, a redriver may also provide gain adjustment, output equalization, de-emphasis, or other signal-conditioning functions.

    Its main functions include:

    • Compensating for frequency-dependent channel insertion loss.

    • Improving signal waveforms affected by inter-symbol interference.

    • Applying equalization to help restore the receiver's eye opening.

    • Supporting longer electrical channels within a defined signal-integrity budget.

    • Providing a relatively low-power alternative to full signal regeneration in suitable applications.

    2. Why Do High-Speed Cables Need Redrivers?

    Electrical signals do not travel through copper cables without degradation. As the signal passes through conductors, connectors, and circuit-board traces, its amplitude and waveform can change. The impact becomes more significant as signaling frequency and cable length increase.

    2.1 Insertion Loss

    Insertion loss is the reduction in signal power caused by an electrical transmission channel. Copper conductors exhibit frequency-dependent losses, meaning higher-frequency signal components can be attenuated more strongly than lower-frequency components.

    This changes the shape of the received waveform. A redriver uses equalization to provide additional gain to the affected frequency components, helping compensate for channel loss.

    2.2 Inter-Symbol Interference (ISI)

    ISI occurs when one transmitted symbol influences the waveform of neighboring symbols. It is commonly associated with bandwidth limitations and frequency-dependent channel loss.

    As ISI increases, the eye opening becomes smaller, making it more difficult for the receiving device to distinguish between data symbols. Redriver equalization can reduce this type of distortion and improve the signal presented to the receiver.

    2.3 Reduced Eye Opening

    An eye diagram is used to evaluate signal quality by displaying multiple signal transitions overlaid on one another. A clear eye opening indicates better timing and voltage margin, while a closed or distorted eye indicates greater difficulty in recovering the transmitted data.

    By compensating for channel loss, a redriver can improve the eye opening when the dominant impairment is equalizable channel distortion.

    2.4 Limited Passive Copper Reach

    Passive DAC cables do not contain active signal-conditioning electronics. Their transmission performance depends on cable construction, conductor size, connector quality, signaling rate, and the electrical characteristics of the connected host ports.

    As channel loss increases, a passive connection may exceed the available transmitter and receiver equalization budget. Adding a redriver can compensate for some of this loss and extend the practical reach of a copper connection.

    3. How Does a Redriver Work?

    A redriver improves signal quality through analog equalization rather than full digital signal regeneration. Its operation can be understood in four stages.

    3.1 Signal Reception

    The redriver receives an electrical signal from the host or preceding cable segment. The incoming signal may have reduced amplitude and waveform distortion due to insertion loss.

    3.2 Frequency-Dependent Equalization

    The input equalizer analyzes the frequency characteristics of the incoming waveform. A CTLE applies different levels of gain across the frequency spectrum, typically emphasizing high-frequency components that have experienced greater channel attenuation.

    The amount of equalization must be selected according to the channel characteristics. Too little equalization leaves excessive ISI, while too much equalization can amplify high-frequency noise and worsen signal quality.

    3.3 Signal Conditioning

    After equalization, the redriver conditions the waveform for transmission through the next electrical segment. Depending on the architecture, this may include output gain, de-emphasis, or other analog signal adjustments.

    3.4 Transmission to the Next Segment

    The conditioned signal is transmitted toward the receiving host. Unlike a retimer, the redriver does not use a clock and data recovery circuit to sample and regenerate the original data stream.

    Host A      Electrical transmitter
    →
    Copper Channel      Insertion loss and ISI
    →
    Redriver      CTLE + Signal Conditioning
    →
    Host B      Electrical receiver

    Simplified signal-conditioning path. Actual cable designs may place active components at one or both ends, depending on the architecture.

    4. What Is CTLE and Why Is It Important?

    Continuous-Time Linear Equalization (CTLE) is one of the most important technologies used in high-speed redrivers.

    In a typical copper channel, high-frequency components experience greater attenuation than low-frequency components. This creates a frequency imbalance that changes the shape of the transmitted signal.

    CTLE compensates for this behavior by applying frequency-dependent gain. It increases the relative strength of higher-frequency components to counteract the channel's low-pass characteristics.

    Its main benefits include:

    • Compensating for frequency-dependent insertion loss.

    • Reducing ISI-related waveform distortion.

    • Improving the eye opening at the receiver.

    • Supporting longer electrical channels within the available signal budget.

    However, CTLE does not distinguish between signal and noise. If excessive equalization is applied, high-frequency noise and crosstalk may also be amplified. Redriver selection and tuning therefore require careful channel analysis and validation.

    5. Redriver vs. Retimer: What Is the Difference?

    Redrivers and retimers are both used to improve high-speed electrical signal transmission, but their internal architectures and signal-processing capabilities are different.

    A redriver performs analog equalization and signal conditioning. A retimer goes further by recovering clock and data, sampling the incoming information, and retransmitting a newly generated signal.

    ParameterRedriverRetimer
    Signal processingAnalog equalization and conditioningClock and data recovery with signal regeneration
    CTLECommonly usedCommonly used
    CDRNoYes
    Jitter handlingCompensates for ISI-related deterministic jitter when properly equalizedCan reduce accumulated jitter through clock recovery and retransmission
    Signal regenerationNoYes
    Processing latencyGenerally very lowHigher due to clock and data recovery
    Power consumptionGenerally lowerGenerally higher
    Implementation complexityLowerHigher
    Common cable applicationACCAEC

    The choice depends on channel insertion loss, jitter requirements, power budget, cable reach, and host equalization capabilities. A redriver is suitable when analog equalization can keep the complete channel within the required signal-integrity limits. A retimer is considered when signal regeneration is necessary.

    6. Redrivers in Active Copper Cables (ACC)

    Active Copper Cables (ACC) integrate redriver or linear equalizer electronics into a copper cable assembly. Their purpose is to extend the practical reach of copper connectivity while avoiding the full DSP and CDR architecture typically associated with retimer-based AECs.

    In a typical ACC design, active equalization is incorporated near the cable ends. The redriver compensates for the cable's insertion loss while maintaining a linear electrical signal path between the host transmitter and receiver.

    6.1 How ACC Uses Redrivers

    A host transmitter sends an electrical signal through the cable assembly. The redriver applies equalization to compensate for channel loss, and the receiving host uses its own receiver equalization to recover the data.

    Because the redriver does not perform CDR or full digital regeneration, the host transmitter and receiver remain important parts of the overall signal-conditioning system.

    6.2 Why ACC Uses Redrivers Instead of Retimers

    ACC designs aim to provide a balance between reach, power consumption, latency, and cost. Redrivers offer a relatively simple way to compensate for channel loss without introducing the additional processing stages of a retimer.

    This architecture can be attractive in high-density data center environments where many short-reach copper connections are deployed and power efficiency is important.

    The ACC MSA focuses on defining electrical requirements for compatible linear-equalizer-based copper cable products, helping establish a more consistent multi-vendor ecosystem.

    7. DAC vs. ACC vs. AEC: Where Do Redrivers Fit?

    DAC, ACC, and AEC cables all use copper conductors, but their internal signal-conditioning architectures are different.

    FeatureDACACCAEC
    Full product nameDirect Attach CopperActive Copper CableActive Electrical Cable
    Signal-processing componentNoneRedriver / linear equalizerRetimer
    EqualizationHost transmitter and receiverActive analog equalizationActive equalization and DSP
    CDRNoNoYes
    Signal regenerationNoNoYes
    Active powerNoYesYes
    Additional processing latencyVery lowVery lowHigher than passive DAC
    Typical design priorityLow cost and powerLow-power signal conditioningSignal regeneration and extended reach

    These are general architectural distinctions rather than fixed performance ratings. Actual reach, power, and interoperability depend on the specific cable, signaling rate, connector, and host platform.

    8. Why Redrivers Matter for 400G and 800G Networks

    High-speed data center connections increasingly rely on faster electrical signaling and more demanding signal-integrity requirements. Redrivers provide a relatively low-complexity method of compensating for channel loss in suitable copper interconnect designs.

    8.1 400G Connectivity

    400G copper interconnects can use multiple high-speed electrical lanes. As lane rates increase, insertion loss and ISI become more important design constraints.

    Redriver-based ACC solutions can provide additional equalization for channels that exceed the practical reach of passive copper while remaining within the supported electrical link budget.

    8.2 800G Connectivity

    800G interconnects introduce further challenges because of higher signaling rates and tighter electrical margins. ACC designs using advanced linear equalization can support certain 800G short-reach connections, provided that the complete host-to-host channel meets the applicable electrical requirements.

    For these applications, redriver bandwidth, equalization range, noise performance, power consumption, and thermal characteristics all need to be considered.

    8.3 AI and High-Performance Computing

    AI infrastructure uses large numbers of high-bandwidth connections between GPUs, servers, network interface cards, and switches. Copper interconnects remain useful for suitable short-reach connections because they can offer low latency and a compact connection architecture.

    Redriver-based ACC solutions provide another option for extending copper reach while controlling active power consumption. They are especially relevant when the host's SerDes capabilities can work with a linear channel.

    9. Key Benefits and Limitations of Redrivers

    9.1 Main Benefits

    • Improved signal quality: Equalization compensates for frequency-dependent insertion loss and reduces ISI-related distortion.

    • Low latency: Redrivers avoid the clock recovery and data regeneration stages of retimers.

    • Lower power requirements: Their simpler analog architecture generally consumes less power than a comparable retimer solution.

    • Lower implementation complexity: They typically require fewer digital signal-processing functions.

    • Extended copper reach: They can help support longer channels than passive copper alone in suitable applications.

    9.2 Main Limitations

    • No clock and data recovery: Redrivers cannot regenerate the bitstream or reset the accumulated jitter budget through CDR.

    • Limited jitter correction: They primarily address ISI-related deterministic jitter; random jitter is not removed.

    • Noise amplification: Equalization can boost noise and crosstalk along with the desired high-frequency signal components.

    • Equalization tuning: The correct settings depend on channel characteristics, and excessive equalization can degrade performance.

    • Channel-dependent reach: A redriver cannot compensate for every type of channel impairment or guarantee a specific cable distance.

    10. What Should Engineers Consider When Selecting a Redriver Cable?

    Selecting a redriver-based cable requires evaluating the entire electrical channel rather than considering the cable assembly in isolation.

    1. Data rate and lane configuration: Verify the supported signaling rate and number of electrical lanes.

    2. Insertion loss: Check whether the redriver's equalization range is sufficient for the complete channel.

    3. Host SerDes capability: Confirm that the switch, NIC, or server transmitter and receiver can operate with the intended linear channel.

    4. Jitter budget: Evaluate both deterministic and random jitter to ensure that the receiving device retains sufficient timing margin.

    5. Noise and crosstalk: Consider whether equalization may amplify unwanted signal components.

    6. Power and thermal requirements: Review the cable's active power consumption and the host port's available power.

    7. Compatibility: Check connector type, electrical interface, cable configuration, management requirements, and platform support.

    8. Validation: Review eye diagrams, BER results, channel measurements, and interoperability test results under the intended operating conditions.

    11. Redriver Technology in C-LIGHT High-Speed Interconnect Solutions

    For high-speed data center connectivity, redriver-based ACC and retimer-based AEC represent two different approaches to active copper transmission.

    Redriver technology is relevant when the application requires analog signal conditioning, low additional latency, and lower active power consumption. Retimer technology is more appropriate when the electrical channel requires clock and data recovery and full signal regeneration.

    When evaluating C-LIGHT copper interconnect solutions, customers should consider the complete application requirements, including:

    • 400G or 800G aggregate data rate.

    • QSFP-DD or OSFP host interface requirements.

    • ACC or AEC signal-processing architecture.

    • Supported cable length and electrical channel budget.

    • Host SerDes compatibility and platform qualification.

    • Power consumption, thermal conditions, and latency requirements.

    Choosing between ACC and AEC should be based on measured channel performance and system requirements, not simply on the advertised data rate. For additional product information, visit the C-LIGHT optical and high-speed interconnect portfolio.

    12. Frequently Asked Questions About Redrivers

    Q1: What does a redriver do in a high-speed cable?

    A redriver compensates for electrical signal loss using analog equalization. It helps improve waveform quality and reduce ISI-related distortion in high-speed cable connections.

    Q2: Is a redriver the same as an amplifier?

    No. A redriver uses frequency-dependent equalization, commonly CTLE, to compensate for channel loss. It does more than apply uniform signal amplification.

    Q3: Does a redriver perform clock and data recovery?

    No. A conventional redriver does not include CDR. It conditions the analog waveform without sampling and regenerating the transmitted data.

    Q4: What is the difference between a redriver and a retimer?

    A redriver performs analog equalization, while a retimer recovers clock and data and retransmits a regenerated signal. Retimers can address a wider range of signal impairments but generally require more power and introduce more processing latency.

    Q5: Why are redrivers used in ACC cables?

    Redrivers help ACC cables compensate for insertion loss while maintaining a linear electrical channel. This can extend copper reach without requiring the full CDR and DSP architecture of a retimer-based AEC.

    Q6: Can a redriver remove random jitter?

    No. A redriver mainly compensates for ISI-related deterministic jitter caused by channel loss. Random jitter generally passes through the device and may also receive additional contributions from its own circuitry.

    Q7: What is CTLE in a redriver?

    CTLE stands for Continuous-Time Linear Equalizer. It applies frequency-dependent gain to compensate for channel insertion loss, particularly the attenuation of high-frequency signal components.

    Q8: Do redrivers consume power?

    Yes. Redrivers are active electronic components that require power for signal conditioning. However, their power consumption is generally lower than that of comparable retimer-based solutions.

    Q9: Can redrivers extend the reach of passive DAC cables?

    Redriver-based active copper designs can extend the practical reach of copper connectivity compared with passive DAC, depending on the cable construction, signaling rate, and available channel budget.

    Q10: Are redrivers suitable for 800G connections?

    Redriver-based solutions can be used in suitable 800G copper architectures. The final choice depends on lane rates, insertion loss, host equalization capability, jitter margin, and electrical compliance.

    13. Conclusion

    Redrivers play an important role in high-speed electrical connectivity by compensating for insertion loss and improving signal quality through analog equalization. Their ability to reduce ISI-related distortion makes them useful in ACC cables and other active copper interconnects.

    Compared with retimers, redrivers offer a simpler, lower-power, and lower-latency approach, but they cannot recover clock and data or eliminate all forms of jitter. As 400G and 800G data center networks expand, selecting the appropriate signal-conditioning architecture requires careful consideration of channel loss, host SerDes capability, power consumption, and overall link performance.

    For any questions, please contact us by email or WhatsApp.

    Email: sales@c-light.com

    WhatsApp: +86 132 6656 7067

    Related Articles

    Call
    Top