C-LIGHT telephone TEL:+86 132 6656 7067    
Language
C-LIGHT search

How Does Liquid Cooling Affect Optical Interconnect Design in AI Data Centers?

By C-LIGHT Marketing 丨 Jun 3, 2025
Table of Contents

    AI data centers are moving toward increasingly dense GPU systems, higher-power switching platforms, and faster optical links. As rack power requirements rise, conventional air cooling alone can become difficult to manage. Direct-to-chip liquid cooling and immersion cooling are therefore becoming important parts of next-generation data center thermal design.

    However, cooling changes more than the way heat is removed from GPUs and CPUs. Optical transceivers, fiber connectors, electrical interfaces, cable assemblies, and optical engines must also operate within the thermal and environmental conditions created by the selected cooling architecture. A module designed for a conventional air-cooled switch cannot automatically be assumed to work reliably when exposed to an immersion coolant.

    The impact on optical interconnect design depends on where the optical components are installed, whether they are exposed to liquid, how heat is transferred, and whether their materials and interfaces have been qualified for the operating environment.

    1. Why Liquid Cooling Is Changing AI Data Center Architecture

    AI training clusters generate substantial heat through GPUs, CPUs, memory, power delivery systems, and high-speed networking equipment. Increasing accelerator density also raises the amount of heat that must be removed from a limited rack footprint.

    Air cooling relies on fans, heatsinks, and controlled airflow to transfer heat away from electronic components. As component power increases, maintaining suitable temperatures may require higher airflow, larger cooling infrastructure, and more careful management of airflow resistance.

    Liquid cooling provides a different heat-transfer approach. Liquids can transport heat more effectively than air in many system configurations, allowing cooling infrastructure to handle higher thermal loads. This does not mean that every component in a liquid-cooled rack is directly cooled by liquid. The actual cooling method depends on the system architecture.

    Cooling ArchitectureCooling MethodOptical Interconnect Implications
    Air coolingFans and heatsinks move air through equipment.Optical modules depend on airflow, heatsink design, inlet temperature, and module power.
    Direct-to-chip liquid coolingCold plates transfer heat from processors and other selected components to circulating coolant.Front-panel optical modules may still rely on air cooling and need independent thermal management.
    Rear-door heat exchangerA liquid-assisted heat exchanger removes heat from air leaving the rack.Airflow through switches and optical modules remains important, even though rack-level heat removal changes.
    Single-phase immersion coolingElectronic equipment is immersed in a dielectric liquid that absorbs heat without boiling.Exposed modules, connectors, cables, and materials require compatibility validation with the immersion fluid.
    Two-phase immersion coolingHeat is absorbed through liquid evaporation and removed through condensation.Component materials and interfaces must be evaluated under the specific fluid and operating conditions.

    For optical network designers, the key distinction is whether the optical interface remains in an air-cooled equipment area or becomes part of a liquid-exposed assembly. These two deployment conditions lead to different engineering requirements.

    2. Direct-to-Chip Cooling Does Not Eliminate Optical Module Heat

    Direct-to-chip cooling is commonly used to remove heat from high-power processors and accelerators. A cold plate is installed on selected components, and coolant circulates through the plate to transfer heat to a cooling distribution system.

    Optical transceivers installed in front-panel switch cages may not be connected to this liquid circuit. They can remain dependent on the switch chassis airflow, even when the GPU or switching ASIC uses liquid cooling.

    This creates a thermal design challenge. A rack may have effective liquid cooling for its processors while optical modules continue to operate in a relatively warm airflow environment. If the optical modules have high power consumption or are installed at high port density, their local temperatures still require attention.

    Several factors influence the temperature of pluggable optical modules:

    • Module power consumption: Higher electrical and optical power requirements increase the amount of heat generated inside the module.

    • Airflow distribution: Uneven airflow can create temperature differences between modules in the same switch.

    • Switch port density: Closely spaced modules can increase local thermal concentration.

    • Inlet air temperature: Warmer air reduces the available temperature margin for module cooling.

    • Heatsink and cage design: Mechanical contact and heat-transfer paths influence how effectively module heat reaches the cooling airflow.

    Consequently, liquid cooling at the server level should not be treated as proof that the networking layer has sufficient thermal capacity. Switches, optical modules, and cable assemblies need to be evaluated as part of the complete rack cooling design.

    3. Immersion Cooling Introduces New Material Compatibility Requirements

    Immersion cooling changes the environment around electronic and optical components more directly. In this architecture, equipment is placed in a dielectric cooling liquid rather than operating in ordinary air.

    Although dielectric fluids are selected for their electrical properties, they can interact differently with materials used in conventional optical modules. A transceiver may contain a metal housing, PCB, optical components, polymers, adhesives, seals, electrical contacts, and connector materials. Each material can respond differently to long-term fluid exposure.

    Material compatibility should therefore be assessed across the complete optical assembly rather than based only on the module housing.

    ComponentPotential ConcernDesign Consideration
    Module housingFluid interaction, corrosion, or changes in surface properties.Verify housing material compatibility with the selected coolant.
    Electrical contactsChanges in electrical interface behavior and contact reliability.Evaluate connector materials and electrical performance in the actual fluid environment.
    PCB and electronic componentsLong-term exposure may affect coatings, components, and assembly materials.Validate the complete electronic assembly under the intended operating conditions.
    Optical connectorsFluid exposure, contamination, and changes in optical interface behavior.Use a qualified connector arrangement and verify optical performance after exposure.
    Adhesives and sealsSwelling, softening, degradation, or loss of sealing performance.Check chemical compatibility and long-term sealing reliability.
    Fiber cable jacketsChanges in flexibility, mechanical strength, or surface condition.Select cable materials qualified for the specific immersion fluid.

    The cooling liquid itself matters. Different dielectric fluids can have different chemical properties, viscosity, operating temperatures, and compatibility characteristics. A component qualified for one fluid should not automatically be considered suitable for another.

    Design consideration: Immersion compatibility is a system-level qualification. A module's operating temperature specification alone does not establish that its housing, electrical contacts, optical connectors, cable jacket, and internal materials are suitable for continuous fluid exposure.

    4. Optical Transceiver Design Must Account for Both Heat and Electrical Performance

    Higher-speed optical transceivers create additional thermal and electrical design demands. As data rates increase, module architectures may require more sophisticated signal processing, optical components, drivers, and receiver circuitry. The resulting power dissipation must be managed within the available mechanical and thermal envelope.

    Liquid cooling can help remove heat from high-density systems, but the cooling method must be compatible with the transceiver's electrical and mechanical interfaces.

    In immersion environments, the dielectric properties of the surrounding fluid can influence electrical interface behavior. High-speed electrical contacts and connectors are generally designed around a specific surrounding dielectric environment. Replacing air with a liquid can change the electrical characteristics of the interface and affect signal integrity.

    This is particularly important for high-speed channels using 112G- and 224G-class electrical signaling. The complete channel includes the host ASIC, PCB traces, connector, module interface, and optical engine. Changes to any part of this path can affect insertion loss, return loss, crosstalk, and overall signal margin.

    Optical transceiver qualification for liquid-cooled systems should therefore cover:

    • Electrical interface performance in the intended operating environment.

    • Optical transmit power, receiver sensitivity, and link stability.

    • Module power consumption and temperature distribution.

    • Mechanical fit and connector engagement.

    • Material compatibility with the specified coolant.

    • Performance after extended exposure and thermal cycling.

    Cooling performance and signal integrity are related engineering concerns, but solving one does not automatically solve the other. Both require independent validation.

    5. Fiber Routing and Connector Design Become More Important

    Liquid-cooled AI racks often use dense arrangements of GPU servers, switches, power distribution equipment, and cooling infrastructure. Optical fiber routing must accommodate this physical layout without interfering with liquid distribution, equipment access, or maintenance procedures.

    Immersion systems introduce additional considerations because fiber connectors and cable sections may be exposed to the cooling fluid. Conventional optical connectors are not automatically designed for continuous immersion. Their performance depends on connector construction, sealing arrangements, material selection, and the specific deployment environment.

    Connector and cable considerations

    • Connector sealing: Optical interfaces exposed to coolant may require specially designed sealing or protected connection arrangements.

    • Fiber routing: Cable paths should avoid excessive bending, mechanical stress, and interference with equipment installation.

    • Jacket compatibility: Cable jacket materials should be tested against the actual immersion fluid.

    • Strain relief: Cable assemblies need suitable mechanical support to reduce stress at module and connector interfaces.

    • Maintenance access: Optical connections should be arranged to support inspection, cleaning, replacement, and system servicing.

    • Optical cleanliness: Connector end-face condition remains important for insertion loss and return loss, including after maintenance.

    For some immersion architectures, a sealed optical module with an attached fiber pigtail can keep the optical path connected while the external fiber interface is positioned outside the liquid environment. Other designs may use an extension arrangement that keeps the pluggable transceiver outside the immersion tank. The appropriate approach depends on system architecture and qualification requirements.

    6. Cooling Architecture Influences Optical Interconnect Placement

    Optical modules do not have to be placed in the same thermal environment as GPUs or CPUs. Their location can be adjusted according to the rack layout, network topology, service model, and cooling strategy.

    In an air-cooled or direct-to-chip liquid-cooled rack, front-panel transceivers can remain in the switch chassis and use a dedicated airflow path. In an immersion-cooled system, designers may need to decide whether the optical module itself will be immersed or whether the optical connection should extend outside the tank.

    Optical PlacementTypical ArchitecturePrimary Design Focus
    Front-panel pluggable opticsAir-cooled switches or networking equipment in liquid-cooled racks.Airflow, module temperature, port density, and service access.
    Immersion-compatible optical moduleOptical module installed within an immersion-cooled system.Fluid compatibility, sealing, electrical interface behavior, and long-term reliability.
    Optical module with attached fiberImmersion-compatible module connected through a fiber pigtail to an external optical interface.Sealed optical path, cable routing, connector protection, and maintenance.
    External optical connectionTransceiver positioned outside the immersion environment, with a suitable cable or extension arrangement.Electrical reach, signal integrity, cable construction, and external module cooling.
    Near-packaged or co-packaged opticsOptical engines located close to the host ASIC or integrated into the package environment.Thermal coupling, optical fiber attachment, packaging, testing, and serviceability.

    Near-packaged optics (NPO) and co-packaged optics (CPO) introduce another dimension to thermal design. Moving optical engines closer to high-power ASICs can reduce electrical interconnect distance, but it also creates new challenges involving heat transfer, thermal gradients, packaging materials, and fiber attachment.

    Liquid cooling may help manage system-level heat, but it does not remove the need to protect optical engines from excessive temperature variation or mechanical stress. The optical and electronic components must be designed together with the package and cooling system.

    7. Optical Interconnect Requirements Across 400G, 800G and 1.6T Networks

    AI data center networks are evolving toward 400G, 800G, and 1.6T optical connectivity. Higher port bandwidth can reduce the number of physical links required for a given aggregate capacity, but it also increases demands on electrical signaling, optical integration, power delivery, and thermal management.

    The cooling requirements of a transceiver depend on its actual design and power consumption, not simply its nominal data rate. Two modules with the same bandwidth can have different thermal characteristics because of differences in reach, optical architecture, DSP implementation, and component selection.

    Network GenerationTypical DeploymentOptical Design ConsiderationsCooling Considerations
    400GLeaf-to-spine links and high-speed server connectivity.QSFP-DD or OSFP form factors, parallel or duplex fiber interfaces, and link-distance requirements.Module power, airflow around switch ports, and chassis thermal capacity.
    800GHigh-density AI fabrics and data center switching.Eight-lane electrical interfaces, optical engine efficiency, and host signal integrity.Higher port-level thermal density and possible need for enhanced system cooling.
    1.6TNext-generation AI switching and high-bandwidth interconnects.224G-class electrical lanes, advanced optical integration, and packaging constraints.Thermal design becomes increasingly important as module and port power requirements rise.

    For large AI fabrics, the optical network may combine short-reach connections within racks, longer links between racks, and DCI links between facilities. These link types have different optical specifications and environmental requirements. A cooling strategy should therefore be matched to the actual placement and operating conditions of each optical component.

    8. C-LIGHT Liquid Immersion Optical Transceiver Solutions

    Optical connectivity in immersion-cooled computing environments requires more than a conventional transceiver operating within a specified temperature range. The module, connector, cable, and surrounding materials must be considered together to support reliable operation in the intended cooling environment.

    C-LIGHT offers a dedicated Liquid Immersion Transceiver product family positioned for AI data centers, high-performance computing systems, and hyperscale GPU clusters.

    Current configurations listed by C-LIGHT:

    ProductPart NumberFiber TypeWavelengthConnectionFiber SpecificationTemperature Grade
    100G QSFP28 to MPOCL100GS4MUIM0.8MMMF850nm0.8mOM3 / MPOIndustrial
    25G/10G SFP28 to UniBoot LCCL25GSLUB-IM0.8MMMF850nm0.8mOM3 / UniBoot LCIndustrial

    These listed configurations provide short-reach multimode optical connections for compact computing and network environments. Their 850nm optical interfaces and 0.8m connection lengths are suited to applications where short internal fiber links are required.

    The product family is positioned for liquid-cooled AI and HPC infrastructure. For a specific deployment, customers should confirm the required coolant type, exposure conditions, connector arrangement, equipment compatibility, and qualification scope with the supplier before installation.

    For broader AI network architectures, C-LIGHT also provides optical transceiver solutions across multiple data rates and application categories. The appropriate module should be selected according to the switch or server interface, transmission distance, fiber type, connector, and network protocol. Relevant options are available through the C-LIGHT Optical Transceiver product range.

    9. Testing and Qualification for Liquid-Cooled Optical Systems

    Optical components intended for liquid-cooled environments should undergo testing that reflects their actual installation conditions. Standard optical performance tests remain necessary, but immersion deployment introduces additional material, electrical, and mechanical qualification requirements.

    A practical qualification program should address the following areas:

    • Optical performance: Measure insertion loss, transmit power, receiver sensitivity, and link stability before and after environmental testing.

    • Thermal performance: Evaluate module temperature under representative operating loads and cooling conditions.

    • Fluid compatibility: Assess exposed materials, including housing, seals, adhesives, connector components, and cable jackets, against the specified coolant.

    • Electrical performance: Verify high-speed electrical interface behavior in the intended operating environment.

    • Mechanical reliability: Check connector retention, cable strain relief, sealing, and mechanical stability.

    • Environmental endurance: Conduct appropriate exposure, thermal cycling, and aging tests based on the expected service conditions.

    • System interoperability: Validate the complete link with the intended switch, server, host interface, and fiber infrastructure.

    Testing should use the actual coolant or a technically justified equivalent under controlled conditions. Exposure duration, temperature, fluid condition, and mechanical configuration should reflect the intended deployment. Passing a short initial test does not necessarily demonstrate long-term compatibility.

    Qualification principle: Optical link performance, material compatibility, and thermal reliability should be evaluated together. A module that passes conventional optical testing may still require additional qualification before it is deployed in an immersion-cooled system.

    10. Conclusion

    Liquid cooling is changing AI data center design by enabling higher computing density and new rack architectures. Its influence extends beyond GPUs and CPUs to the optical interconnects that connect servers, switches, and distributed computing resources.

    In direct-to-chip systems, front-panel optical modules may continue to depend on airflow even when processors are liquid-cooled. In immersion systems, exposed modules, electrical interfaces, fiber connectors, and cable materials must be evaluated for compatibility with the selected dielectric fluid. Meanwhile, 400G, 800G, and 1.6T network generations increase the importance of managing power density, signal integrity, and optical packaging.

    Successful deployment requires a coordinated design approach covering cooling architecture, module placement, fiber routing, material selection, electrical performance, and environmental qualification. By matching optical interconnect solutions to the actual operating environment, AI data center operators can build network infrastructure that supports higher bandwidth while maintaining reliability and serviceability.

    Planning optical connectivity for a liquid-cooled AI data center?

    C-LIGHT provides optical transceiver solutions, compatibility support, and customized engineering services for data center and high-performance computing applications. Contact the C-LIGHT team to discuss module specifications, fiber interfaces, and deployment requirements.

    Contact C-LIGHT

    For any questions, please contact us by email or WhatsApp.

    Email: sales@c-light.com

    WhatsApp: +86 132 6656 7067

    Related Articles

    Call
    Top