A 400G AOC (Active Optical Cable) is a factory-terminated optical cable assembly designed to provide 400Gbps connectivity between compatible network devices. It integrates optical transceiver components at both ends with a multimode fiber cable, allowing electrical signals from the host equipment to be converted into optical signals for transmission and converted back into electrical signals at the receiving end.
Unlike a 400G DAC, which uses copper conductors, a 400G AOC transmits data through optical fiber. This makes it a practical option for short-reach connections in data centers, AI computing environments, high-performance computing (HPC) clusters, and high-density switching networks.
Available in interfaces such as QSFP-DD, QSFP112, and OSFP112, 400G AOC solutions can support direct 400G connections as well as selected 400G-to-100G and 400G-to-200G breakout configurations.
1. How Does a 400G AOC Cable Work?
A 400G AOC combines two active optical ends and a permanently attached fiber cable into one assembly. Each end contains optical and electrical components that connect directly to a compatible switch, server, or other networking device.
1.1 Electrical-to-Optical Conversion
When a switch or server sends data through its 400G port, the electrical signals enter the AOC's transmitting end. The internal optical engine converts these signals into optical signals, which travel through the multimode fiber.
At the receiving end, photodetectors convert the incoming optical signals back into electrical signals for the connected device. The process operates in both directions, supporting full-duplex communication.
1.2 Integrated Optical Components
Unlike a conventional optical link that requires separate pluggable transceivers and fiber patch cords, an AOC combines the optical interfaces and cable into one factory-assembled product. This reduces the number of individual components that need to be installed and managed.
1.3 Multi-Lane Transmission
400G connectivity uses multiple high-speed lanes rather than relying on a single low-speed channel. For example, 400GBASE-SR8 uses eight optical lanes in each transmission direction, with each lane operating at approximately 50Gbps. Other 400G optical implementations use different lane architectures, so the lane count and signaling method should be checked against the specific AOC design.
2. Key Specifications of a 400G AOC Cable
The specifications of a 400G AOC depend on its form factor, optical architecture, fiber type, and intended application. The following table summarizes the configurations listed in the C-LIGHT 400G AOC product family.
| Parameter | C-LIGHT Listed Specifications |
|---|---|
| Data Rate | 400Gbps |
| Form Factors | OSFP112, QSFP112, QSFP-DD |
| Optical Wavelength | 850nm |
| Fiber Type | Multimode Fiber (MMF) |
| Fiber Grade | OM3 |
| Cable Length | 1m–30m |
| Connection Types | 400G-to-400G, 400G-to-4x100G, 400G-to-2x200G |
| Applications | Data Centers, InfiniBand Networks, HPC, AI Infrastructure |
These specifications describe the configurations currently listed by C-LIGHT, not a universal specification for every 400G AOC. Cable length, interface, protocol, and breakout support must be confirmed for the selected part number.
3. Common 400G AOC Form Factors
The form factor determines how the AOC connects to network equipment. The choice depends on the switch or server port, mechanical requirements, and supported data rate.
3.1 400G QSFP-DD AOC
QSFP-DD (Quad Small Form-Factor Pluggable Double Density) is a widely used high-speed transceiver form factor. A 400G QSFP-DD AOC integrates QSFP-DD interfaces at both ends and provides a direct cable connection between compatible QSFP-DD ports.
QSFP-DD AOC configurations are commonly considered for 400G switch-to-switch and switch-to-server connections. C-LIGHT also lists QSFP-DD breakout options for connecting a 400G port to multiple lower-speed interfaces.
3.2 400G QSFP112 AOC
QSFP112 is designed for higher-speed electrical interfaces and is used in 400G networking platforms. A 400G QSFP112 AOC provides an integrated optical connection between compatible QSFP112 ports.
It is particularly relevant to high-performance networking and InfiniBand environments. Port compatibility and supported protocol should be verified before deployment.
3.3 400G OSFP112 AOC
OSFP112 (Octal Small Form-Factor Pluggable) is another form factor used in high-speed data center networks. A 400G OSFP112 AOC connects compatible OSFP112 ports through an integrated optical cable assembly.
OSFP-based solutions are often selected for platforms designed around high-density, high-bandwidth switching. The host equipment must support the specific OSFP interface and operating mode.
4. 400G AOC Breakout Configurations
Not every network connection requires the same port speed at both ends. Breakout AOCs allow one 400G interface to connect to multiple lower-speed interfaces, provided that the host switch supports the required port breakout mode.
4.1 400G to 4x100G AOC
A 400G-to-4x100G breakout AOC connects one 400G port to four independent 100G ports. This arrangement is useful when a high-speed switch needs to connect with multiple 100G devices or when a network is migrating from 100G to 400G infrastructure.
C-LIGHT lists configurations including 400G QSFP-DD to 4x100G QSFP56 AOC. This allows a single 400G connection to be distributed across four compatible 100G interfaces.
4.2 400G to 2x200G AOC
A 400G-to-2x200G breakout AOC divides one 400G connection into two 200G links. It can be used in networks where 200G server or switch ports coexist with 400G uplinks.
Available C-LIGHT configurations include OSFP112-to-2x200G OSFP112, OSFP112-to-2x200G QSFP112, and selected QSFP-DD-based combinations.
| Breakout Type | Port Configuration | Typical Use |
|---|---|---|
| 400G to 4x100G | 1 × 400G to 4 × 100G | Connecting multiple 100G ports |
| 400G to 2x200G | 1 × 400G to 2 × 200G | Connecting two 200G ports |
| 400G to 400G | 1 × 400G to 1 × 400G | Direct high-speed interconnection |
Breakout compatibility is determined by the switch ASIC, port configuration, firmware, and cable design. A breakout cable alone cannot make an unsupported port operate in a different mode.
5. 400G AOC vs. 400G DAC vs. 400G AEC
400G AOC, DAC, and AEC cables all provide high-speed connectivity, but they use different transmission media and signal-conditioning approaches. Selecting the right type requires considering link distance, power consumption, cable routing, and equipment compatibility.
| Feature | 400G DAC | 400G AEC | 400G AOC |
|---|---|---|---|
| Transmission Medium | Copper | Copper | Optical Fiber |
| Signal Processing | Passive | Active Signal Conditioning | Electrical-Optical Conversion |
| Typical Reach | Very Short | Short | Longer Short-Reach Links |
| Power Consumption | Lowest | Higher than Passive DAC | Requires Power at Both Ends |
| EMI Sensitivity | More Sensitive | More Sensitive | Immune to Optical-Link EMI |
| Weight and Flexibility | Can Be Bulky | Copper Cable Construction | Generally Lighter for Longer Runs |
| Typical Application | Short Rack-Level Links | Extended Copper Links | Short-Reach Optical Links |
5.1 400G AOC vs. 400G DAC
The main difference is the transmission medium. A 400G DAC uses copper conductors to carry electrical signals directly between devices, while a 400G AOC converts electrical signals into optical signals for transmission through fiber.
DAC is generally preferred for very short connections where low power consumption and cost are priorities. AOC is more suitable when the connection requires greater reach, lighter cabling, or immunity to electromagnetic interference.
5.2 400G AOC vs. 400G AEC
A 400G AEC uses copper conductors with active electronic components to improve signal quality over a longer distance than a comparable passive DAC. A 400G AOC uses optical fiber and integrated optical conversion instead.
AEC can be useful when a deployment needs to retain a copper-based connection while extending its practical reach. AOC is a better fit when optical transmission and reduced electromagnetic interference are important.
For related cable options, see C-LIGHT AEC solutions.
6. Applications of 400G AOC Cables
6.1 AI Data Center Networks
AI training and inference clusters generate substantial traffic between GPUs, compute nodes, and network switches. 400G AOC cables can provide high-bandwidth optical links in short-reach sections of these networks, helping connect equipment within and between racks.
For deployments using InfiniBand, the cable's interface and protocol support must match the network fabric. Ethernet and InfiniBand compatibility should not be assumed to be interchangeable.
6.2 High-Performance Computing
HPC environments require high-throughput, low-latency communication between compute nodes and storage systems. 400G AOC links can support high-speed interconnections in cluster networks where bandwidth and cable management are important.
6.3 Data Center Leaf-Spine Networks
In leaf-spine architectures, switches exchange traffic through high-speed uplinks. 400G AOC cables can connect compatible 400G ports over short distances, supporting high-capacity links between network layers.
6.4 Switch-to-Switch Connections
When two switches are located in the same rack or nearby racks, a 400G AOC can provide a direct optical connection without requiring separate transceivers and patch cords.
6.5 Server and Storage Interconnection
High-performance servers and storage systems can use 400G connections to support demanding data-transfer workloads. AOC configurations are useful when the host interfaces, cable length, and supported protocol match the system requirements.
7. How to Select the Right 400G AOC Cable
Choosing a 400G AOC involves more than matching the 400G data rate. The following factors should be checked before placing an order or installing the cable.
7.1 Confirm the Host Interface
Identify the physical interface on both connected devices. QSFP-DD, QSFP112, and OSFP112 are different form factors and are not directly interchangeable. Confirm the exact connector type and supported port mode at each end.
7.2 Check the Required Cable Length
Measure the actual cable route, including vertical routing, cable trays, and service loops. Select a length that provides sufficient routing allowance without creating unnecessary cable congestion.
C-LIGHT lists 400G AOC lengths from 1m to 30m. The available length depends on the specific product configuration.
7.3 Verify Fiber and Wavelength
Check the optical wavelength and fiber type specified by the AOC. C-LIGHT's listed 400G AOC family uses 850nm multimode transmission over OM3 fiber. Do not assume that all 400G AOCs use the same optical design or fiber grade.
7.4 Confirm Ethernet or InfiniBand Support
Some 400G AOC configurations are designed for Ethernet, while others are specified for InfiniBand. Confirm the protocol supported by the cable and the connected equipment, particularly in AI and HPC networks.
7.5 Check Breakout Compatibility
For 400G-to-100G or 400G-to-200G connections, verify that the switch supports the intended breakout mode. Check the lane mapping, port configuration, and remote device interface before selecting the cable.
7.6 Verify Platform Compatibility
Check the switch or server vendor's compatibility requirements, including supported cable types, firmware, management interface, and power specifications. A matching connector does not automatically guarantee operational compatibility.
8. C-LIGHT 400G AOC Product Configurations
C-LIGHT provides several 400G AOC configurations for data center and high-performance networking applications. The product family includes direct connections and breakout options using different form factors.
| Configuration | Part Number | Data Rate | Fiber / Wavelength | Listed Length |
|---|---|---|---|---|
| OSFP112 to OSFP112 | CLOP4-OP4AOC-xx | 400G / 400G | OM3 / 850nm | 1–30m |
| QSFP112 to QSFP112 | CLQ112-Q112AOC-xx | 400G InfiniBand | OM3 / 850nm | 1–30m |
| QSFP-DD to QSFP-DD | CLQD4-QD4AOC-xx | 400G InfiniBand | OM3 / 850nm | 1–30m |
| QSFP-DD to 4xQSFP56 | CLQD4-4xQ56AOC-xx | 400G to 4x100G | OM3 / 850nm | 1–30m |
| OSFP56 to 2xQSFP56 | CLOP4-2xQ56AOC-xx | 400G to 2x200G | OM3 / 850nm | 1–30m |
| QSFP-DD to 2xQSFP56 | CLQD4-2xQ56AOC-xx | 400G to 2x200G | OM3 / 850nm | 1–30m |
| QSFP-DD to 2xQSFP-DD | CLQD4-2xQD2AOC-xx | 400G to 2x200G | OM3 / 850nm | 1–30m |
| OSFP112 to 2xOSFP112 | CLOP4-2xOP2AOC-xx | 400G to 2x200G | OM3 / 850nm | 1–30m |
| OSFP112 to 2xQSFP112 | CLOP4-2xQP2AOC-xx | 400G to 2x200G | OM3 / 850nm | 1–30m |
For complete specifications, part number details, and available configurations, visit the C-LIGHT 400G AOC product page.
9. Frequently Asked Questions About 400G AOC
Q1: What does 400G AOC stand for?
400G AOC stands for 400G Active Optical Cable. It is an integrated cable assembly that uses optical fiber and active optical components to provide 400Gbps connectivity.
Q2: What is the maximum distance of a 400G AOC?
Reach depends on the optical design and fiber specification. C-LIGHT lists its current 400G AOC configurations with cable lengths from 1m to 30m.
Q3: Does a 400G AOC require separate optical transceivers?
No. The optical components are integrated into both ends of the cable assembly, so separate pluggable transceivers and fiber patch cords are not required.
Q4: What wavelength does a 400G AOC use?
C-LIGHT's listed 400G AOC products use an 850nm optical wavelength with OM3 multimode fiber. Other 400G AOC designs may use different optical specifications.
Q5: What is the difference between 400G AOC and 400G DAC?
A 400G AOC transmits data through optical fiber, while a 400G DAC uses copper conductors. AOC is generally more suitable for longer short-reach connections, while DAC is often preferred for very short, low-power links.
Q6: Can a 400G AOC connect to four 100G ports?
Yes. A 400G-to-4x100G breakout AOC can connect one 400G port to four 100G ports when the host equipment supports the required breakout configuration.
Q7: Is 400G AOC suitable for AI data centers?
Yes. It can provide short-reach, high-bandwidth connections in AI clusters, GPU networks, and high-performance computing environments. The protocol and interface must match the network platform.
Q8: Can 400G AOC be used for InfiniBand?
Yes. Certain 400G AOC models are designed for InfiniBand applications. Check the product specification to confirm protocol support rather than assuming that every 400G AOC supports InfiniBand.
Q9: Which form factors are available for 400G AOC?
Common options include QSFP-DD, QSFP112, and OSFP112. The appropriate form factor depends on the ports available on the connected switches or servers.
Q10: How do I choose the right 400G AOC cable?
Confirm the host interface, supported protocol, cable length, optical specifications, breakout requirements, and equipment compatibility before selecting a model.
10. Conclusion
A 400G AOC cable provides an integrated optical solution for high-bandwidth, short-reach connections in modern data center networks. By combining optical interfaces and multimode fiber into one assembly, it simplifies installation and supports flexible connections between switches, servers, and high-performance computing systems.
With QSFP-DD, QSFP112, and OSFP112 options, along with 400G-to-100G and 400G-to-200G breakout configurations, C-LIGHT's 400G AOC product family supports a range of network deployment requirements. Selecting the correct model requires careful attention to interface compatibility, protocol support, fiber specifications, and cable length.
For more information, visit C-LIGHT 400G AOC or browse the C-LIGHT AOC product range.
TEL:+86 132 6656 7067




















































>
>
>
>
>
>
>
>