A 1.6T Direct Attach Copper (DAC) cable is a high-bandwidth electrical interconnect designed to support data rates of up to 1.6Tbps between compatible network devices. Built for next-generation data centers, AI infrastructure, GPU clusters, and high-performance computing (HPC), it provides short-reach connectivity without the optical conversion required by fiber-based interconnects.
The transition from 800G to 1.6T brings significant changes to electrical signaling and cable construction. Newer 1.6T DAC designs use 200G-class PAM4 electrical lanes or alternative multi-lane configurations, depending on the interface architecture. These higher-speed signals require carefully engineered twinaxial conductors, connector transitions, and shielding to maintain signal integrity.
Available in advanced form factors such as OSFP1600 and OSFP-XD, 1.6T DAC solutions are designed for high-density switching systems and short connections within next-generation computing infrastructure.
1. What Is a 1.6T DAC Cable?
A 1.6T DAC cable is a factory-terminated copper cable assembly that connects two compatible 1.6T electrical interfaces. It integrates high-speed copper conductors and connector modules into one assembly, eliminating the need for separate optical transceivers and fiber patch cables.
Unlike an optical interconnect, a passive 1.6T DAC carries electrical signals directly through twinaxial copper pairs. The host devices handle signal transmission, equalization, and data recovery, while the cable provides the physical electrical channel.
Its main characteristics include:
Aggregate bandwidth: Up to 1.6Tbps, depending on the supported interface.
Transmission medium: High-speed shielded twinaxial copper.
Signal format: PAM4 for current 200G-class electrical lanes.
Connector options: OSFP1600, OSFP-XD, and other platform-specific interfaces.
Deployment: Short-reach connections inside high-density racks and computing systems.
Power efficiency: Passive versions require no active signal-conditioning power in the high-speed data path.
Unlike a generic copper cable, a 1.6T DAC is engineered for a specific high-speed electrical interface. Connector compatibility, lane mapping, channel loss, and host support must all be considered.
2. How Does a 1.6T DAC Achieve 1.6Tbps?
The 1.6Tbps aggregate rate is achieved by transmitting data across multiple electrical lanes simultaneously. Two important architectural approaches are emerging in 1.6T copper interconnect designs.
2.1 Eight 200G-Class PAM4 Lanes
One common 1.6T implementation uses eight transmitting lanes and eight receiving lanes, with each lane operating at approximately 200Gbps of nominal data rate.
These lanes use 224G-class PAM4 electrical signaling. The higher physical signaling rate provides the capacity required to support the 1.6T interface.
| Parameter | 8-Lane 1.6T Architecture |
|---|---|
| Aggregate data rate | 1.6Tbps |
| Electrical lanes | 8 TX + 8 RX |
| Nominal data rate per lane | 200Gbps class |
| Electrical signaling | 224G-class PAM4 |
| Transmission medium | Twinaxial copper |
| Typical application | 1600G Ethernet and InfiniBand XDR implementations |
Volex's OSFP1600 passive DAC datasheet provides a representative example: eight transmitting and eight receiving 224Gbps PAM4 channels, supporting 1600GBASE-CR8 and InfiniBand XDR applications.
2.2 Sixteen 100G Electrical Lanes
Another approach uses 16 electrical lanes, each carrying approximately 100Gbps of nominal data. This architecture can also provide an aggregate bandwidth of 1.6Tbps.
For example, OSFP-XD cable designs are available with a 16-lane, 100G-per-lane architecture. This arrangement uses more differential pairs than an eight-lane 200G design and requires a different connector and cable assembly architecture.
| Feature | 8 × 200G | 16 × 100G |
|---|---|---|
| Aggregate bandwidth | 1.6Tbps | 1.6Tbps |
| Lane count per direction | 8 | 16 |
| Nominal lane rate | 200Gbps | 100Gbps |
| Representative architecture | OSFP1600 | OSFP-XD |
| Differential pair count | 16 pairs total for TX/RX | 32 pairs total for TX/RX |
These are different electrical implementations of the same aggregate bandwidth. They should not be treated as interchangeable cable designs. The host interface, connector pinout, lane mapping, and cable specification determine which architecture is supported.
3. What Is the Role of 224G PAM4 Signaling?
224G PAM4 is a key electrical signaling technology for next-generation 1.6T interfaces. It increases the amount of information carried by each electrical lane while keeping the number of lanes manageable.
3.1 Four-Level Signal Modulation
PAM4 stands for Pulse Amplitude Modulation with four levels. Each symbol represents two bits of information through four different signal amplitudes.
Compared with NRZ, which uses two signal levels and carries one bit per symbol, PAM4 doubles the number of bits transmitted at the same symbol rate.
| Feature | NRZ | PAM4 |
|---|---|---|
| Signal levels | 2 | 4 |
| Bits per symbol | 1 | 2 |
| Data capacity | Lower | Twice NRZ at the same symbol rate |
| Voltage separation | Larger | Smaller |
| Signal integrity requirements | Less demanding in comparable conditions | More demanding |
3.2 Why 224G Signaling Is More Demanding
At 224G-class signaling rates, the electrical channel becomes increasingly sensitive to insertion loss, return loss, crosstalk, and impedance discontinuities.
The smaller voltage separation between PAM4 levels also reduces the available signal margin. Cable materials, conductor geometry, shielding, connector design, and manufacturing consistency therefore become critical to reliable operation.
4. How Is a 1.6T DAC Cable Constructed?
A 1.6T DAC uses high-performance twinaxial copper conductors arranged into multiple differential pairs. Each pair carries a high-speed electrical signal, while shielding and insulation help preserve the required electrical characteristics.
4.1 Twinaxial Copper Conductors
Twinaxial construction places two conductors within a controlled dielectric structure. This supports differential signaling and helps maintain the impedance characteristics required by high-speed electrical interfaces.
Depending on the architecture, a 1.6T cable may contain 16 or 32 differential pairs. The exact configuration depends on whether the design uses eight 200G-class lanes or sixteen 100G-class lanes.
4.2 Shielding and Insulation
High-speed copper cables use carefully designed insulation and shielding structures to reduce electromagnetic interference and crosstalk between adjacent pairs.
Typical construction elements include:
Copper conductors: Carry high-speed differential signals.
Dielectric insulation: Maintains electrical separation and controlled impedance.
Individual pair shielding: Limits coupling between adjacent signal pairs.
Overall cable protection: Provides additional mechanical and electromagnetic protection.
Outer jacket: Protects the cable assembly during installation and operation.
Advanced dielectric materials and conductor treatments can help reduce signal loss while maintaining mechanical flexibility. Cable diameter, bending performance, and airflow also matter in high-density rack deployments.
4.3 Connector and PCB Design
The electrical channel does not end at the copper cable. Signals must pass through connector contacts and PCB traces at both ends of the assembly.
At 224G-class signaling rates, these transitions require careful impedance control and low-loss routing. Poorly designed transitions can introduce reflections, insertion loss, and crosstalk that reduce the available signal margin.
5. OSFP1600 vs OSFP-XD: Different 1.6T DAC Architectures
OSFP1600 and OSFP-XD represent different approaches to high-density electrical connectivity. Both can support 1.6Tbps aggregate bandwidth, but their lane arrangements and connector architectures differ.
5.1 OSFP1600
OSFP1600 implementations commonly use eight 200G-class electrical lanes. A representative passive cable design uses 16 differential pairs in total, corresponding to eight transmit and eight receive lanes.
Volex's OSFP1600 passive DAC datasheet specifies 224Gbps PAM4 channels, a 16-pair differential twinax cable, and example cable lengths of 0.5m and 1m, with a 1.5m option listed as pending final qualification.
5.2 OSFP-XD
OSFP-XD uses a higher-density electrical interface. Representative 1.6T cable designs use 16 lanes at 100Gbps per lane, requiring 32 differential pairs across the transmit and receive paths.
This architecture provides another route to 1.6T bandwidth, but it requires its own compatible host ports, connector pinout, and cable assembly.
| Feature | OSFP1600 | OSFP-XD |
|---|---|---|
| Aggregate rate | 1.6Tbps | 1.6Tbps |
| Representative lane configuration | 8 × 200G | 16 × 100G |
| Electrical pair count | 16 differential pairs | 32 differential pairs |
| Connector architecture | OSFP1600 | OSFP-XD |
| Compatibility | OSFP1600-compatible host ports | OSFP-XD-compatible host ports |
The OSFP name alone does not establish electrical compatibility. Always verify the exact connector generation and host platform requirements before selecting a cable.
6. What Is the Difference Between 1.6T DAC, ACC, and AEC?
DAC, ACC, and AEC all use copper as the transmission medium, but their signal-conditioning architectures are different.
| Feature | Passive DAC | ACC | AEC |
|---|---|---|---|
| Transmission medium | Copper | Copper | Copper |
| Signal processing | Host-side equalization | Redriver or linear equalization | Retiming with CDR |
| Active electronics | No active signal-conditioning IC in the high-speed path | Yes | Yes |
| Power consumption | Lowest | Higher than passive DAC | Higher than passive DAC |
| Latency | Very low | Low, design-dependent | Includes retiming latency |
| Primary advantage | Simple and power-efficient | Electrical signal conditioning | Clock and data recovery |
6.1 Passive DAC
A passive DAC provides a direct electrical path between the two host devices. It does not include a redriver or retimer in the high-speed data path.
This architecture offers low power consumption and very low latency. Its practical reach, however, depends on the signal capabilities of both host devices and the electrical performance of the complete cable channel.
6.2 Active Copper Cable (ACC)
An ACC typically uses redrivers or linear equalization to compensate for electrical channel loss. This can extend the usable reach compared with a passive cable, although the actual performance depends on the specific design.
6.3 Active Electrical Cable (AEC)
An AEC uses retimers with clock and data recovery (CDR) to recover and retransmit electrical signals. This provides more extensive signal regeneration than a conventional redriver-based active copper design.
For 1.6T systems, passive DAC, ACC, and AEC should be evaluated according to the required distance, host SerDes capabilities, power budget, and latency requirements.
7. What Is the Transmission Distance of a 1.6T DAC?
1.6T DAC cables are designed primarily for short-reach connections. At 200G-class electrical lane rates, insertion loss and signal distortion become significant constraints, making cable length more challenging than in earlier generations.
Published product examples illustrate the short-reach nature of these connections:
| Product Architecture | Example Cable Length | Qualification |
|---|---|---|
| Volex OSFP1600 passive DAC | 0.5m and 1m | Published options; 1.5m listed as pending final qualification |
| Volex OSFP-XD passive DAC | 0.5–1.5m | Listed as preliminary product lengths |
| C-LIGHT 1.6T DAC series | 1m | Listed configurations use 1m, 26 AWG copper assemblies |
These figures are manufacturer-specific examples, not universal maximum reach specifications. Actual support depends on the electrical interface, cable construction, host equipment, and qualification results.
For longer connections, an active copper solution or optical interconnect may be more appropriate. The choice should be based on the complete link budget and deployment layout rather than the aggregate data rate alone.
8. Why Are 1.6T DAC Cables Important for AI Data Centers?
AI infrastructure places increasing demands on network bandwidth. Large GPU clusters require high-speed connections between compute nodes, switches, and storage systems, while high-density rack designs leave limited space for additional cabling.
1.6T DAC technology addresses short-reach interconnection requirements in these environments.
8.1 GPU Cluster Connectivity
High-performance computing systems rely on fast communication between GPUs and network interfaces. Compatible 1.6T DAC connections provide a high-bandwidth electrical path for short connections within rack-scale architectures.
8.2 Higher Port Bandwidth
Moving from 800G to 1.6T doubles the aggregate bandwidth available at a port. This can reduce the number of separate physical connections required for a given bandwidth target, subject to the network architecture and port configuration.
8.3 Lower Power for Short Links
Passive DACs avoid optical conversion and do not require active signal-conditioning electronics in the high-speed cable path. This makes them attractive where the electrical channel can support the required performance without active components.
8.4 Rack-Level Interconnection
Short-reach copper links can connect adjacent switches and computing systems while reducing the need for separate optical transceivers and fiber patch cords. Their suitability depends on cable length, port placement, airflow, and cable-management requirements.
9. 1.6T DAC Breakout Configurations
Some 1.6T cable assemblies support breakout connectivity, allowing one high-bandwidth port to connect to multiple lower-speed ports. This is useful when integrating different generations of networking equipment.
A representative configuration is:
| Connection | Aggregate Bandwidth | Application |
|---|---|---|
| 1 × 1.6T to 1 × 1.6T | 1.6Tbps | Direct high-speed connection |
| 1 × 1.6T to 2 × 800G | 1.6Tbps | Breakout to two 800G interfaces |
The breakout configuration must be supported by the host switch, port mapping, connector design, and cable assembly. A physical breakout cable alone cannot enable an unsupported port mode.
10. C-LIGHT 1.6T DAC Cable Solutions
C-LIGHT's 1.6T DAC product family is designed for short-reach copper connectivity in next-generation data centers, AI/GPU clusters, HPC systems, and storage networks.
The product range includes QSFP-DD, OSFP, and QSFP224 interfaces, with straight-through and breakout configurations for different host platforms.
| Configuration | Interface | Length | Cable Gauge |
|---|---|---|---|
| 1.6T to 1.6T | QSFP-DD to QSFP-DD | 1m | 26 AWG |
| 1.6T to 2 × 800G | QSFP-DD breakout | 1m | 26 AWG |
| 1.6T to 1.6T | OSFP to OSFP | 1m | 26 AWG |
| 1.6T to 2 × 800G | OSFP breakout | 1m | 26 AWG |
Available mechanical designs include Flat-to-Flat, Flat-to-Flat RHS, and Finned-to-Finned IHS configurations. These options address different chassis, port-layout, and cooling requirements.
The listed product family supports 1600G and 800G InfiniBand XDR applications, depending on the selected model. Commercial and industrial temperature options are also available for specified configurations.
For detailed part numbers and compatibility information, visit the C-LIGHT 1.6T DAC product page.
11. Key Factors When Selecting a 1.6T DAC Cable
Choosing a 1.6T DAC requires careful attention to the host platform and electrical interface. A matching aggregate data rate is not sufficient to guarantee compatibility.
11.1 Confirm the Electrical Architecture
Determine whether the platform uses an eight-lane 200G-class interface or a sixteen-lane 100G architecture. Check the required lane mapping and electrical specifications.
11.2 Match the Connector Form Factor
Verify whether the equipment uses OSFP1600, OSFP-XD, or another supported interface. Mechanical compatibility and electrical compatibility must both be confirmed.
11.3 Verify Ethernet or InfiniBand Support
1600G Ethernet and InfiniBand XDR are different application environments. Confirm the cable's supported protocol, host port mode, and relevant interoperability requirements before deployment.
11.4 Select the Correct Cable Length
Choose a cable length supported by the manufacturer's qualification data. Avoid assuming that a 1.6T passive DAC supports the same distance as an 800G or 400G model.
11.5 Check Mechanical and Thermal Requirements
For OSFP systems, check whether the application requires an Integrated Heat Sink (IHS) or a Riding Heat Sink (RHS) mechanical configuration. The cable end design must match the host cage and cooling arrangement.
12. Conclusion
A 1.6T DAC cable is a next-generation copper interconnect designed to provide up to 1.6Tbps of aggregate bandwidth between compatible high-speed network devices. Its architecture uses advanced PAM4 signaling and precision twinaxial conductors to support demanding short-reach electrical connections.
Two important implementation approaches are eight 200G-class lanes and sixteen 100G lanes. OSFP1600 and OSFP-XD designs illustrate these different approaches, each with its own connector architecture and host compatibility requirements.
For AI data centers and HPC infrastructure, 1.6T DAC cables offer a low-power, low-latency option for suitable rack-level connections. Selecting the correct cable requires matching the electrical lane architecture, connector form factor, protocol, cable length, and thermal design to the target equipment.
Frequently Asked Questions
Q1: What is a 1.6T DAC cable?
A 1.6T DAC is a high-speed copper cable assembly designed to provide up to 1.6Tbps connectivity between compatible networking and computing interfaces.
Q2: What does 1.6T mean?
1.6T represents an aggregate data rate of 1.6 terabits per second, equivalent to 1,600Gbps.
Q3: Does a 1.6T DAC use 224G PAM4?
Many 8-lane 1.6T implementations use 224G-class PAM4 electrical signaling, with each lane carrying approximately 200Gbps of nominal data.
Q4: How many lanes does a 1.6T DAC have?
Common architectures include eight 200G-class lanes or sixteen 100G lanes per direction. The actual configuration depends on the interface design.
Q5: What is the difference between OSFP1600 and OSFP-XD?
OSFP1600 commonly uses eight 200G-class lanes, while representative OSFP-XD designs use sixteen 100G lanes. Their connector architectures and host compatibility requirements differ.
Q6: What is the typical reach of a 1.6T passive DAC?
Published product examples are generally short, often around 0.5–1.5m. Actual supported lengths depend on the cable design and host qualification.
Q7: Is a 1.6T DAC compatible with 800G ports?
Some breakout assemblies support one 1.6T interface connected to two 800G interfaces, provided the host platforms and cable mapping support that configuration.
Q8: What is the difference between 1.6T DAC and 1.6T AEC?
A passive DAC carries electrical signals directly, while an AEC uses retimers and clock and data recovery to regenerate signals within the cable assembly.
Q9: Is 1.6T DAC used in AI data centers?
Yes. It is designed for short-reach, high-bandwidth connections in AI clusters, GPU systems, HPC infrastructure, and next-generation data center networks.
Q10: Does C-LIGHT offer 1.6T DAC cables?
Yes. C-LIGHT offers 1.6T DAC configurations with QSFP-DD and OSFP interfaces, including straight-through and 1.6T-to-2×800G breakout options.
TEL:+86 132 6656 7067




















































>
>
>
>
>
>
>
>