C-LIGHT telephone TEL:+86 132 6656 7067    
Language
C-LIGHT search

What Is Insertion Loss in High-Speed Copper Cables?

By C-LIGHT Marketing 丨 Jul 24, 2025
Table of Contents

    As data rates increase in data centers and high-performance computing networks, maintaining signal integrity across copper interconnects becomes increasingly challenging. One of the most important electrical characteristics affecting transmission performance is insertion loss.

    Insertion loss describes how much signal power is reduced as an electrical signal travels through a cable, connector, or other transmission component. In high-speed copper cables, the loss generally increases with frequency, making it more difficult to preserve signal quality at higher data rates.

    For Direct Attach Copper (DAC) assemblies and other Twinax-based interconnects, insertion loss influences usable cable length, receiver equalization requirements, and overall link reliability.

    1. What Is Insertion Loss?

    Insertion loss is the reduction in signal strength caused by inserting a transmission component into a signal path. In a copper cable, part of the electrical signal energy is dissipated or otherwise lost as the signal travels through the conductors and dielectric material.

    It is commonly expressed in decibels (dB) and measured across a range of frequencies. A higher insertion loss means that less of the original signal reaches the receiving end.

    For a transmission path characterized by its forward transmission coefficient S21, insertion loss is commonly expressed as:

    Insertion Loss (dB) = -20 × log10(|S21|)

    Here, S21 represents the voltage-wave transmission coefficient under the specified measurement conditions. In a standard matched 50-ohm measurement system, it is commonly obtained from a vector network analyzer (VNA).

    For example, if the magnitude of S21 is 0.5, the insertion loss is approximately 6 dB. This means the transmitted voltage-wave amplitude is half the incident amplitude under the measurement reference conditions.

    Insertion loss is usually presented as a positive attenuation value. In S-parameter plots, however, S21 is often displayed as a negative value in dB. These are two ways of presenting the same transmission behavior.

    2. Why Does Insertion Loss Occur in Copper Cables?

    Insertion loss in high-speed copper cables results from several physical mechanisms. Their combined effects become more significant as signal frequency increases.

    2.1 Conductor Loss

    Electrical resistance in copper conductors converts part of the signal energy into heat. At higher frequencies, current tends to concentrate near the conductor surface, a phenomenon known as the skin effect.

    As frequency rises, the effective cross-sectional area carrying current becomes smaller, increasing the conductor's AC resistance. This causes greater attenuation of high-frequency signal components.

    2.2 Dielectric Loss

    The insulating material surrounding copper conductors also contributes to signal attenuation. When an alternating electric field passes through a dielectric, some energy is dissipated within the material.

    Dielectric loss depends on the material's properties, including its loss tangent, as well as the operating frequency. Low-loss dielectric materials are therefore important in high-performance cable designs.

    2.3 Connector and Interface Loss

    Connectors, contacts, solder joints, and transitions between cable and equipment can introduce additional attenuation. Poorly controlled impedance or discontinuities at these interfaces may also create reflections.

    Although connector-related effects are often discussed alongside insertion loss, reflection-related problems should also be evaluated through return loss and other impedance measurements.

    2.4 Cable Length

    Longer cables generally produce greater insertion loss because the signal travels through more conductor and dielectric material.

    For a given cable construction and frequency, attenuation per unit length can be used to estimate the cable's distributed loss. However, the total channel loss must also account for connectors, adapters, and other components.

    3. How Frequency Affects Insertion Loss

    Insertion loss is frequency-dependent. A copper cable does not attenuate every frequency component equally.

    Higher-frequency components generally experience greater conductor and dielectric losses than lower-frequency components. As a result, a high-speed digital signal can become distorted even when its overall amplitude remains sufficient for basic detection.

    Digital signals contain multiple frequency components. When higher-frequency components are attenuated more strongly, the shape of the received waveform changes. This can reduce edge sharpness and increase inter-symbol interference (ISI).

    This is one reason why a cable that performs adequately at a lower data rate may not meet the requirements of a higher-speed interface, even if the physical cable length remains unchanged.

    4. How Insertion Loss Affects High-Speed Copper Cable Performance

    Insertion loss directly affects the electrical channel between a transmitter and receiver. Excessive attenuation can reduce the available signal margin and make reliable data recovery more difficult.

    4.1 Reduced Received Signal Amplitude

    As the signal travels through the cable, its amplitude decreases. If the received signal becomes too weak relative to the receiver's noise and detection limits, the probability of bit errors increases.

    4.2 Increased Inter-Symbol Interference

    Frequency-dependent attenuation changes the shape of digital signal transitions. Energy from one symbol can spread into neighboring symbol intervals, making it harder for the receiver to distinguish consecutive data symbols.

    4.3 Reduced Signal Margin

    High-speed links operate within defined electrical performance limits. Greater insertion loss consumes part of the available signal margin, leaving less tolerance for variations in cable characteristics, connector quality, temperature, and manufacturing.

    4.4 Greater Equalization Requirements

    Receivers and transmitters may use equalization techniques to compensate for channel loss. However, equalization has practical limits and cannot recover information that has been overwhelmed by noise or severe distortion.

    4.5 Shorter Practical Transmission Distance

    At a given signaling rate, a cable with higher attenuation may support a shorter practical transmission distance. This is why high-speed copper interconnects are generally used for relatively short connections, while optical interconnects are selected when longer reach is required.

    5. Insertion Loss in DAC and Twinax Cables

    Direct Attach Copper cables commonly use Twinax conductors to carry high-speed differential electrical signals between switches, servers, storage systems, and other network equipment.

    Because DAC cables transmit electrical signals directly through copper conductors, their channel performance depends on conductor geometry, dielectric properties, shielding, cable length, and connector design.

    Insertion loss is an important consideration when selecting a DAC assembly for a specific data rate and distance.

    DAC CharacteristicEffect on Insertion Loss
    Cable lengthLonger cable generally produces greater attenuation.
    Conductor designConductor dimensions and material properties affect resistance and high-frequency loss.
    Dielectric materialMaterial loss contributes to frequency-dependent attenuation.
    Connector designInterface transitions contribute to total channel loss.
    Operating frequencyHigher-frequency components generally experience greater attenuation.
    Manufacturing consistencyVariations can affect impedance, attenuation, and overall channel performance.

    Passive DAC cables rely on the electrical characteristics of the cable assembly and the host interfaces. Active DAC cables incorporate electronic circuitry to improve signal transmission performance in supported applications. Their capabilities and supported lengths depend on the specific product design.

    C-LIGHT provides DAC cable solutions for high-speed data center interconnections. Cable selection should be based on the required data rate, port compatibility, length, and electrical specifications of the complete link.

    6. Insertion Loss vs. Return Loss vs. Crosstalk

    Insertion loss is only one part of high-speed channel characterization. Return loss and crosstalk describe different signal integrity problems and should not be treated as interchangeable measurements.

    ParameterWhat It MeasuresPrimary CauseTypical Impact
    Insertion LossSignal attenuation through the transmission pathConductor and dielectric losses, channel componentsReduced received signal strength and waveform distortion
    Return LossSignal reflection caused by impedance mismatchImpedance discontinuities and interface transitionsReflections and possible signal distortion
    NEXTNear-end crosstalkCoupling between adjacent signal pathsInterference measured near the transmitting end
    FEXTFar-end crosstalkCoupling between adjacent signal pathsInterference measured near the receiving end

    These parameters are often evaluated together when testing high-speed copper channels. A cable with low insertion loss may still have unacceptable return loss or crosstalk, so a complete channel assessment requires more than one measurement.

    7. How Is Insertion Loss Measured?

    Insertion loss is commonly measured using a vector network analyzer (VNA). The instrument evaluates how a signal passes through the device or cable under test over a specified frequency range.

    7.1 S21 Measurement

    S21 is the forward transmission parameter in a two-port network measurement. It indicates how much of the incident signal at port 1 is transmitted to port 2.

    For a cable assembly, the S21 response is measured across the required frequency range. The resulting curve shows how attenuation changes as frequency increases.

    7.2 Differential Insertion Loss

    High-speed copper cables commonly carry differential signals. For differential channels, engineers use mixed-mode S-parameters to evaluate differential transmission behavior.

    The differential insertion loss parameter is generally identified as Sdd21. It characterizes the forward transmission of a differential signal through the channel.

    7.3 Frequency Sweep

    A VNA performs measurements across a defined frequency range rather than at only one frequency. This makes it possible to identify frequency-dependent attenuation and determine whether the channel meets its applicable insertion loss limits.

    7.4 Fixture and Calibration Considerations

    Accurate measurements require suitable test fixtures, calibration, and de-embedding where appropriate. Test cables, adapters, connectors, and fixture transitions can affect the measured result.

    For meaningful comparisons, the measurement setup, reference planes, frequency range, and test conditions should be consistent.

    8. What Is an Insertion Loss Budget?

    An insertion loss budget defines the maximum attenuation permitted across a transmission channel under specified operating conditions.

    It is an important design consideration because the cable is only one part of the complete electrical path. The host transmitter, PCB traces, connectors, cable assembly, and receiver all contribute to channel performance.

    A simplified channel loss calculation can be expressed as:

    Total Channel Insertion Loss = Cable Loss + Connector Loss + PCB Loss + Other Channel Losses

    This expression is a conceptual loss budget. Actual compliance evaluation must follow the measurement reference planes and channel definitions in the applicable interface specification. Loss contributions should not be added without considering the relevant measurement conditions and interactions between channel elements.

    When selecting a cable, engineers should verify that its insertion loss performance leaves sufficient margin for the rest of the channel. A cable that meets its own specification does not automatically guarantee that the complete link will pass compliance testing.

    9. How to Reduce Insertion Loss in High-Speed Copper Cables

    Reducing insertion loss requires controlling both the cable's physical construction and the electrical channel design.

    9.1 Use Low-Loss Dielectric Materials

    Materials with lower dielectric loss can reduce attenuation, particularly at higher frequencies. Material selection is therefore an important part of high-speed Twinax cable design.

    9.2 Optimize Conductor Geometry

    Appropriate conductor dimensions and consistent geometry help control resistance and high-frequency transmission characteristics. The design must also maintain the required impedance and mechanical properties.

    9.3 Control Cable Length

    Using the shortest practical cable length can reduce distributed attenuation. However, the selected length must also meet installation and equipment-layout requirements.

    9.4 Improve Connector Transitions

    Well-designed connectors and controlled transitions help minimize additional channel loss and impedance discontinuities.

    9.5 Select the Correct Cable Assembly

    Different DAC assemblies support different data rates, lengths, and host interfaces. Selecting a cable based on its actual electrical specifications is more reliable than choosing one based only on connector appearance or nominal compatibility.

    9.6 Consider Optical Interconnects for Longer Reach

    When the required distance or bandwidth exceeds the practical capabilities of a copper channel, optical connectivity may be a better solution. AOC assemblies and optical transceivers use fiber to transmit data over longer distances without the same electrical conductor attenuation mechanisms.

    C-LIGHT offers Active Optical Cable (AOC) solutions for applications where optical transmission is appropriate.

    10. Insertion Loss and Higher Data Rates: 400G, 800G, and Beyond

    As Ethernet speeds increase, electrical channels must preserve signal quality over wider frequency ranges. This places greater demands on cable assemblies, connectors, PCB layouts, and host interfaces.

    Higher-speed signaling does not automatically mean that insertion loss doubles. The actual channel requirements depend on the modulation format, symbol rate, equalization architecture, channel specification, and operating conditions.

    For example, PAM4 carries two bits per symbol, allowing a higher bit rate without requiring the same symbol rate as an NRZ system carrying an equivalent amount of data. However, PAM4 has smaller amplitude separation between adjacent signal levels, making signal-to-noise performance and channel distortion especially important.

    In 400G and 800G systems, the electrical lane architecture and supported cable length must be evaluated together. The insertion loss limit for a specific link should always be taken from the relevant interface specification or equipment requirements rather than inferred from the aggregate data rate alone.

    11. How to Evaluate DAC Cable Insertion Loss Before Deployment

    Before deploying high-speed DAC assemblies, network engineers should evaluate the complete channel against the intended application.

    • Confirm the interface: Verify the switch and server port type, data rate, and supported electrical lane configuration.

    • Check cable length: Confirm that the selected length is supported at the target data rate.

    • Review insertion loss: Examine the frequency-dependent insertion loss curve rather than relying on a single attenuation value.

    • Check return loss and crosstalk: Evaluate other important signal integrity parameters alongside insertion loss.

    • Verify equalization support: Confirm that the host transmitter and receiver can compensate for the expected channel characteristics.

    • Validate interoperability: Test the cable with the intended equipment and operating conditions.

    For large-scale data center deployments, consistent cable performance is important for maintaining predictable link behavior across multiple racks and network connections.

    12. Frequently Asked Questions About Insertion Loss

    Q1: What does insertion loss mean in a copper cable?

    Insertion loss is the reduction in signal strength as an electrical signal travels through a cable or transmission component. It is usually measured in decibels.

    Q2: Why does insertion loss increase with frequency?

    Conductor resistance increases at higher frequencies due to the skin effect, while dielectric losses also contribute to greater attenuation.

    Q3: Does a longer DAC cable have higher insertion loss?

    Generally, yes. A longer cable introduces more conductor and dielectric attenuation, although actual performance depends on cable construction and frequency.

    Q4: What is S21 in insertion loss testing?

    S21 is the forward transmission parameter of a two-port network. Its magnitude is used to calculate insertion loss.

    Q5: What is the difference between S21 and Sdd21?

    S21 describes single-ended forward transmission, while Sdd21 describes differential-mode forward transmission in a mixed-mode S-parameter measurement.

    Q6: Is insertion loss the same as return loss?

    No. Insertion loss measures transmitted signal attenuation, while return loss characterizes signal reflections caused by impedance mismatch.

    Q7: How does insertion loss affect high-speed DAC cables?

    Excessive insertion loss reduces received signal margin, increases waveform distortion, and can make reliable data recovery more difficult.

    Q8: Can equalization compensate for insertion loss?

    Equalization can compensate for certain channel losses and distortion, but it cannot fully recover signals when attenuation and noise exceed the receiver's capabilities.

    Q9: How is copper cable insertion loss measured?

    A vector network analyzer measures transmission parameters such as S21 or differential Sdd21 across a specified frequency range.

    Q10: When should DAC be replaced with AOC?

    AOC is worth considering when the required distance, data rate, cable routing, or electrical channel performance exceeds the practical capabilities of the selected DAC solution.

    Conclusion

    Insertion loss is a fundamental signal integrity parameter in high-speed copper cables. It describes how much signal attenuation occurs as an electrical signal travels through a cable assembly and its associated interfaces.

    For DAC and Twinax connections, conductor resistance, skin effect, dielectric properties, cable length, and connector transitions all influence insertion loss. As data rates increase, controlling these factors becomes essential for maintaining adequate signal margin and reliable transmission.

    Evaluating insertion loss together with return loss, crosstalk, and equalization capability helps engineers select suitable copper interconnects for high-speed data center networks. When copper channel limitations become restrictive, AOC and optical transceiver solutions provide alternative connectivity options.

    For any questions, please contact us by email or WhatsApp.

    Email: sales@c-light.com

    WhatsApp: +86 132 6656 7067

    Related Articles

    Call
    Top